wiring

I got this RZR1-2500D mono amp rated for a min. of 2ohm, but will it run at 1ohm (with no issues) if I were to wire up my 12” Kicker compr 2ohm dual voice coils for a 1ohm load? Not able to spend any money currently and not trying to blow up my amp or sub fr.. Any help or maybe someone who has...

hey i have a simple question with Hopefully a simple answer now the setup I have going is not practical I know i know that I don't have them running in a efficient way but any how I have taramps hd3000 1 ohm to a power acoustic mofo 122x dvc 2ohm @ 4ohm and a rockville db15 running a power...

I have a Skar RP-800.1D, it is a monoblock with 2 sets of speaker terminals. I know that this is for easier wiring/ more space for wires. My question is when I wire this into my DVC sub, can I just run + to +, + to +, - to -, and - to -, and would this end up as parallel wiring? -For any...

Hello, I am currently working on my second audio install and my amp isn't wanting to turn on. I have checked with my multimeter the voltage coming from the power wire and the remote wire while the car is on and it shows 14+ volts. But as soon as I connect the blue remote turn on wire to the...

This question may be quite straight forward, but I cannot find an answer anywhere. I am new to this forum but I found the formula to ballpark estimate my total amperage. I do not understand one part. When you calculate this, do you add up the total RMS of the amplifier AND the subwoofers it will...

So I've had this problem for a couple months now, I've got 2x12 inch MTX Terminator subs (I know they're not the greatest) and every few weeks, usually when a song has some hard low frequency bass, the fuse that is connected to the power wire under my hood will blow, causing the subs to stop...

So I don’t know why or how but when I plug both rcas into the amp they distort the sub and when I have only one it will play one sub crystal clear and I don’t know what to do from here any help would be appreciated thanks

I just installed a new head unit JVC KD-S29 in my 08 Ford Focus which has an existing display separate from the factory radio unit I was wondering if there is any way to link my new head unit display to the factory display. Also I used a single din head with no harness adapter instead of the...

So to start things off I have a 2008 Infiniti G35X with the stock head unit with an Alpine MRX-M100 mono amp hooked up using pre-amp the signal going to stock Bose amp, a Singer 200 amp alternator, AGM battery, DC Audio Level 2 wired at 2 ohms and 0 gauge Knukoncepts OFC power and ground. I...

Hi everyone, I installed a cheap head unit ( unsure of the brand at the moment ) both in my wife’s car and mine. Everything worked fine for a little while in my 98 4runner and then one day all of a sudden there was just no power to the radio. I pulled the unit out and checked the 15 amp fuse...

First, Ford F-150 Fuse #23 (10A) Details: Power driven rear glass switch. [Not Implemented] Inverter. Driver side window. Moonroof. [Not Implemented] Vista roof. [Not Implemented] I currently have a Dashcam wired into a fuse tap to fuse #23 10A in my interior truck fuse box. Can devices...

Yesterday night I finished up putting my new sound system in my car. I was playing with it to find my sweet spot this morning and I went to get some food and as I rolled my window down to order, my speakers just suddenly stopped. I was wondering if I just nicked the wires or should I be more...

So basically I have a pioneer 5100nex model head unit in my 2001 Audi A6 and I’m trying to figure out if the head unit is messed up or if it’s something else. The instructions for installing the head unit say that it can NOT be installed in a vehicle without an ACC switch on the ignition and my...

I have a kenwood 9104d amp. I did some research on it and it says it does 900 rms at 2 ohms and is regulated down to a lil over 900 at 1 ohm .I had dual 12 punch p3s (2ohm) and wound up blowing 1 of them. my friend gave me a power acoustic gothic. It's a 4ohm dvc. I know it's not good to have...

I currently have a 2005 Mazda 3 sp23 and I currently have a kicker compr 12" sub with an Alpine amp, pioneer A-series 6x8 in front and rear, a Kenwood dpx303mbt head unit, and factory sail panel tweeters. I wanted to put a kicker keysmart amp to the speakers but do I need anything for the...

Okay so Im new to this and I bought an suv with a system in it and it was all professionally installed but sold the existing system for something smaller, anyways so I installed these ds18 12’s with a ds18 amp and and hooked up everything and when I turned on my suv i noticed the amp never...

Hey guys, I'm running a Skar RP1200, MTX 7512-22 @ 1 Ohm and an Audio Control LC2i. I just did the install while keeping the factory head unit in my 2016 Ford Focus ST. I spliced into the factory wire harness coming from the factory Sony amp to grab signal from the front speakers (using solder...

So I can either wire each sub’s coils in parallel to create 1 ohm each, then wire the subs in series to create a total of 2 ohm load. OR I can wire each sub’s coils in series to create 4 ohms each, then wire the subs in parallel to create a total of 2 ohm load. Does it matter which way I go with?

I bought a 2007 scion Tc that has an aftermarket Pioneer HU installed and I wanted to replace it with a newer Kenwood HU. The previous owner had payed for an install of an amp and 2 subs which sound great. When I swapped the 2 radios I am unable to get the amp and sub to power on. I am assuming...

Hi, thanks in advance for any help. I've added a leisure battery to my van, using the wiring in this video: https://youtu.be/oOQHe_cZtI4?t=1044 I have this amp: https://www.caraudiocentre.co.uk/product_m-pioneer-gm-d8704_p-41014.htm and this head...

Okay here is the scenario. I am starting a build next month. I’m doing this one for a family member and they have a conversion van because my family member recently became handicapped.  They love a decent sound system seems to be a genetic thing haha, anyway all this started with a need for 120...

I am in the process of replace the factory head unit (sony no nav) with another head unit (power acoustik with nav) and when I went to create a wiring harness, I noticed there were no negative speaker connections coming from original head unit.. So my question is, should I ground the ones coming...

Hey, all I recently just installed an Alpine type S 12" sub in my 2013 Ford Police Interceptor. While I'm driving, the sub randomly spikes up in volume, and then does back down again. There's no coherent pattern that would link it to acceleration or braking. Some context: Ive got a Clarion...

So I bought the cheapest car around and of course, it has a crap sound system. fortunately, I had 2 pair of speakers laying around: - PIONEER TS-R6951S 400W 3-Way (this one I want to put in the back) - Boston exl-60c 25w RMS 220w (and these ones in rear passenger seats) and I plan to buy...

Hi! So my current setup are Dual 6x9 200w rear deck and Dual 5.25 in the front doors. I’m wanting to know if it would be possible to mount 6x9 speakers in the rear doors and splice them to existing wires. Would this cause any issues with power to my speakers?   Would doing this result in...

Hello, I would like to know how to connect a crossover to the amplifier. there are 2 crossovers that have 2 way and 3 way they have in+ and in- and for tweeters, sub and medium. thanks regards

Helloooooo Just to be clear i literally know nothing about car audio installations and i need help so i came here. I have a renault clio hatchback 2007 and i am wishing to install the skar audio spx-65c component system to the vehicle i dont want it to be runnning very loud, so i would like...

I ordered the head unit, wiring harness from crutchfield as well as a little controller module thing and another harness so the steering wheel controls will work. However, looking at the instructions provided by crutchfield, it says that both of the wiring harnesses need to connect to the...

If anyone can lend some knowledge please help out . i have an aftermarket stereo with recently upgraded door speakers , now I am trying to install a 5 channel amp and subwoofer so I could boost all the door speakers and also power my subwoofer.  I’m pretty confused on which wires have to run...

Hi, I’m hoping someone can help me find the right adaptor for my car stereo. It’s my first car, a Volkswagen Beetle 2001, and the stereo is a Sony one (see photos). The previous stereo was taken out of the car so I’m not sure if I have all the right wires to get this one set up. I’ve attached...

I have two separate Kicker compR loaded enclosures, both 2 ohms 500 rms. I currently have one set up and am looking for a new amp to wire up the other, looking around i can't find anyone talking about how to wire this considering its an enclosure, i was wondering how they would be set up using a...

Okay so basically right now my setup consists of a sundown u12 and it's wired to 1ohm I've even checked this with a multimeter the amp is a hiphonics Zeus zxx-1800.1d mono amp. My voltages stay around 14-11 when playing music (I know I know) and im getting nothing out of this speaker. It's rated...

Hey guys I'm brand new to this forum and need a little help. I apologize up front if this question has already been answered. If so please shoot me a link. I've scoped the internet far and wide and can't find a good answer. Anyway, let's get to the point. I'm in the works of new audio build and...

Hello friends. My amp and sub setup in my trunk works well except that the amp overheats regularly. It's a 4-channel amp, so I have two options for wiring the sub: bridged and unbridged. When it's unbridged, it's weak but it doesn't overheat as much. When it's bridged it sounds awesome but...

Background: About four or five years ago I installed a pair of American Bass XD-10s wired to two ohms, powered by a Precision Power BK 1300.1D wired up with 4G Knu Koncepts. Relatively soon after installing, my enclosure slid across my trunk and the amp was ripped off of its mounts (two broke...

I have the nvx jad 800 4 channel amp: 4 ohms: 125 watts x 4 chan 2 ohms: 200 watts x 4 chan Bridged, 4 ohms: 400 x 2 chan I have a pair of Alpine components: Peak Power: 330W RMS Power: 110W 4 Ohms Impedance I have a Pioneer DEH-x6900BT head unit: front, rear and sub preouts Questions...

Hey guys, I’m new to the car audio scene so bare with me, I recently got a kicker 4 channel amp that I want to use to give my kicker 6x9 lower door subs some more kick. My questions is do I have to run the speaker wire from the amp to the speakers or can I get away with connecting the speaker...

Hi everyone - I am a new member on the forum and need a little help understanding something (and believe me I've searched and searched on this issue using google, forums, vendor sites, car sites, Youtube, images, amplifier and component speakers manuials, etc. and have found nothing to help...

I can’t figure out if I have the right wiring harness or not. My harness doesn’t have the 2 orange wires and most of the wires don’t even connect to anything on other side. Like the wires are not even connected. I can’t not find any other harness that has orange wires Item(s)...

I just picked up a sundown audio sae 1500 to run my sundown audio sa12 rev 3 d2 and right now have them wired bridged ran in series parellel. I feel like i have them wired all wrong and am not getting the full power of what this amp can do. Am i right or am i wrong...that im wrong?