Quick recommendation on 2 ch amp for my fronts

[BOOMINGRANDPA 5,000+ posts]

No, Infinity speakers are not 4 ohms but may be 2 or a bit more depending on the specific set.

yeah they maybe 3 ohm u think that'll make most amps drop to 2 ohm

 

[slm9s]

After doing some reading, I raised my budget a bit and ended up going with a Zapco ST-4X SQ. Thanks for all your advice.

 

[Papermaker85 5,000+ posts]

After doing some reading, I raised my budget a bit and ended up going with a Zapco ST-4X SQ. Thanks for all your advice.

good ******* CALL

#finallysomeonewithsense !

 

[BOOMINGRANDPA 5,000+ posts]

yeah nice amp., shocked s/n is that low..

 

[LosIsATool 5,000+ posts]

yeah nice amp., shocked s/n is that low..

It's a cheap China amp. You can't have it all.

Quality is hit and miss also.

 

[BOOMINGRANDPA 5,000+ posts]

It's a cheap China amp. You can't have it all. Quality is hit and miss also.

omg u back?, only seen your evil twin past week.. i told him check orion xtr 250 and 500.1 anyone know if they good cause price sure is right on those..

 

[Papermaker85 5,000+ posts]

It's a cheap China amp. You can't have it all. Quality is hit and miss also.

BULLSHIT

you don't know what your talking about they have great build quality.

a few people have posted internals and they look pristine and use higher end opamps.

 

[Papermaker85 5,000+ posts]

4-Channel, Full Range, Class A/B

SQ Upgrades: Op-amps, Caps, Etc.

Tiffany style Panel Mount RCA’s

RCA and Speaker Level Inputs

Variable input gain control

Variable electronic crossover

Auto-on with Speaker level inputs

Compact chassis

Variable bass boost control

Specifications

Power @ 4Ω: 4 x 65 watts

THD @ Rated Power

Power @ 2Ω: 4 x 95 watts

Power Bridged @ 4Ω: 2 x 190W RMS

Signal to Noise Ratio > 90dB

THD + Noise

Channel Separation >60dB

Frequency Response 15Hz to 30KHz ±1dB

Input Sensitivity .25v to 5v

Dimensions in mm: 160(W) x 52(H) x 282(L) Overall: 160(W) x 52(H) x 320(L)

 

[LosIsATool 5,000+ posts]

BULLSHITyou don't know what your talking about they have great build quality.

a few people have posted internals and they look pristine and use higher end opamps.

Ok. I'm not going to sit here and waste my time with you. It's a $150 amp. It's made in china. You win.

 

[Jeffdachef 5,000+ posts]

No such thing as a wrong opinion buddy. //content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif
There's absolutely no point to argue with a post whore. I'm gonna be the bigger man here.

you hypocrite. lol

Calling linear power amps high end made your credibility fly out the window... sorry.

 

[mahc 10+ year member]

you hypocrite. lol

I've been called worst than that. Who's perfect? I see your point but lp amps are known gimmicks.

 

[slm9s]

yeah they maybe 3 ohm u think that'll make most amps drop to 2 ohm

Excuse my ignorance, but does this mean I should not bridge the amp to run my two Infiniti fronts? I think the specs on the Zapco state a value for bridged only on a 4 ohm load...

 

[BOOMINGRANDPA 5,000+ posts]

Excuse my ignorance, but does this mean I should not bridge the amp to run my two Infiniti fronts? I think the specs on the Zapco state a value for bridged only on a 4 ohm load...

yeah man we missed ohm load except trumpet, where u get it at ebay? be great if sell let u trade it.. we assume 4 ohm on speakers unless someone tells us, one of those 60x2 would worked., 3ohm bridged load (=1.5ohm stereo) is pushing your luck, the amp will at least run hot..

 

[slm9s]

I just looked it up, my fronts are Kappa 60.5cs. 3 sites online show them to be 4 ohm.

 

[BOOMINGRANDPA 5,000+ posts]

I just looked it up, my fronts are Kappa 60.5cs. 3 sites online show them to be 4 ohm.

wow man u may be better off to actually pull one out and look at back see if it say 4 or 3 ohm on it, if 4 u can bridge it if 3 run in stereo u be fine and just don't use rear channels of amp and every 6 months u can swap wires on amp to other 2 channels lol 1/2 amp run 1/2 amp gets a break lol.. and later u may think about adding 2nd set of coax or something.. if they 3 ohm eventually u maybe better off going with 65 or 75x2 2 channel if u don't add speakers..