Silverado DDZ build

[raptor727 10+ year member]

I am selling my dual bracket for 150 wish I knew you needed one

 

[wew lad 5,000+ posts]

I am selling my dual bracket for 150 wish I knew you needed one

I need one

what brand is it?

pm me so we dont spam his build

 

[adulbrich 5,000+ posts]

I am selling my dual bracket for 150 wish I knew you needed one

Dang, mine was about $300

I need one
what brand is it?

pm me so we dont spam his build

It's fine.

Good deal for you

 

[adulbrich 5,000+ posts]

I moved the front baffle so the port is now on the driver's side

Then I put the last side on the box

I'm going to do one more layer on that side, and at least one more up top. Probably two more on the top.

Then I'm cutting the holes for the subs, coating the inside with fiberglass resin, and bracing it with threaded pipe.

 

[raptor727 10+ year member]

I need one
what brand is it?

pm me so we dont spam his build

Pm'ed

 

[los33 10+ year member]

I moved the front baffle so the port is now on the driver's side

Then I put the last side on the box

I'm going to do one more layer on that side, and at least one more up top. Probably two more on the top.

Then I'm cutting the holes for the subs, coating the inside with fiberglass resin, and bracing it with threaded pipe.

Dat glue tho...

Also 489$ could of got you a quad alt setup with no belt included //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Sent from my draconis using Tapatalk

 

[adulbrich 5,000+ posts]

Dat glue tho...
Also 489$ could of got you a quad alt setup with no belt included //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Sent from my draconis using Tapatalk

I'm putting another layer over that panel, so the extra glue running didn't matter

I'm happy with my alternator decision, haha

 

[wew lad 5,000+ posts]

separate electrical because different voltage or you just dont want to hurt the stock system?

 

[adulbrich 5,000+ posts]

A few reasons.

1. I won't have as much noise in my mids/highs. The 4 channel will be hooked up to the stock system, which is isolated from my battery bank. Therefore, the noise that the 20.2k dumps won't be an issue.

2. I won't have to replace my starting battery, which is brand new, but lead-acid.

3. I can run a different voltage, and accessories like headlights won't give me voltage drop.

There were a few more that I've forgotten.

 

[Massive spl]

I'm putting another layer over that panel, so the extra glue running didn't matter
I'm happy with my alternator decision, haha

That other panel won't sit flush then if there is lumpy dried glue on it.

 

[adulbrich 5,000+ posts]

That other panel won't sit flush then if there is lumpy dried glue on it.

Sanding will fix that.

I gust poured on the glue to make sure it was a good seam, geez

 

[Boomin_tahoe 5,000+ posts]

Ever sand glue? lulz.

It ain't fun son.

 

[adulbrich 5,000+ posts]

If you get a chisel under the edge, it comes right off. Had to remove glue today when I moved the baffle

 

[wew lad 5,000+ posts]

I'm sure he knows what needs to be fixed when it's that obvious, gotta give him a chance... going to school full time and working is a bitch. some of you lazy motherfuckers wouldn't understand unless you worked a 60-80hr week. I used to start school at 7, get off at 2 go to work and not get off until 10 or later

 

[adulbrich 5,000+ posts]

Thanks. I work on it when I can.

I'm off all this week, because Brenda is a spiteful bitch, haha