Chevyaudio Build Log **Pictures/Video**

[Chevyaudio 5,000+ posts]

Alrighty, Well as some of you know I have been re working most of my audio setup this summer between working and being lazy it has taken quite some time, but now the light at the end of the proverbial tunnel is in sight.

Here is a list of what is/will be used:

(2)Fi Car Audio BL 10"

(1)Incriminator Audio 20.1

(pair) Pioneer Premier 720prs Components [run active]

(1)JBL GTO 75.4 [100x4 @ 4]

(1) Pioneer Premier 880prs Headunit

(2) Deka Intimidator group 31 batteries

(100 ft) 1/0ga. wire

(1) mobile video 7" overhead monitor

(1) Playstation 2

(1) 260amp HO Alternator

That's all I can think off the top of my head...but another 20.1 MIGHT be added in the future or I may switch to a single 40.1...BIG MAYBE.

But anyway to describe the install, the BL's are in a 3.0cu ft. enclosure tuned to 36hz via a flared slot port, the 20.1 and batteries along with their respective distribution hardware, the JBL amp will be housed in a center console along with a stinger voltage meter and will be under Plexiglas that is illuminated with blue LED's.

Most of this hardware I already had left over from my various SPL builds...THATS why the electrical system is so beefy...but I have a feeling that this truck might make a few more appearances this year in the lanes.

Termlab numbers will come tomorrow...too late to meter here at the house, the neighbors don't appreciate it.

well on to what everyone is here for pictures and videos.

Again, I believe in doing things right the first time so as some of you may remember I loom and secure ALL wires.

900amps of fusing

This is what I have to do to run 6 runs of 1/0 through my truck...thank god we have a lift at the shop

Relay for turning everything on

power wire for JBL amp (notice the color coding...that helps tons when troubleshooting

Click to read more...

 

[Chevyaudio 5,000+ posts]

Now some build pictures...im not a huge fan of stopping to take pictures while I build, so most of these are completed pictures.

box and edge of console

Fitting the voltage meter

yummy flair

The flare was done freehand as my table saw wont rip wide enough...I think it came out pretty decent :shrug:

Console and you can see one of the baffles for the mids next to it

random picture of the wall 'o' dash kits/wiring harnesses at the shop

How I left my truck every night for a week or two

720prs

 

[Chevyaudio 5,000+ posts]

And Temp install...finishing things up tomorrow

 

[ThomasG 5,000+ posts]

Sick!!

 

[Chevyaudio 5,000+ posts]

Video.

Rear wall is moving quite a bit though the camera doesnt seem to be picking it up to well.



and anyone who has a single cab...knows how hard it is to make shit flex.

 

[InsaneKreationz]

zomg.

 

[surftb15 10+ year member]

wow, I am impressed. Thats the way everyone should lay down their power wire in an install.

Good job.

 

[DBfan187 5,000+ posts]

Are you a midget?

 

[Chevyaudio 5,000+ posts]

Are you a midget?

no...im 6'

I just sacrafice...its not that bad actually...my knees dont touch the dash.

 

[djman37 5,000+ posts]

good job Cliffy! Now get to Big D!

 

[mikey060 10+ year member]

those speakers are sick..suede surround ftw //content.invisioncic.com/y282845/emoticons/yumyum.gif.0556df42231b304b9c995aefd13928a8.gif

nice build btw

 

[Wkbdkid 10+ year member]

Sweet lookin build. Out of curiosity how tall are you? Cause with that box doesnt look like you have a lot of legroom.

 

[tapout 5,000+ posts]

great work. Cant wait to see numbers.

 

[InsaneKreationz]

Do work.

 

[DBfan187 5,000+ posts]

I'm the same height and there would be no way I could give up that much room!