built a new box, got metered. two 10s and sundown power.

CRXBMPN
5,000+ posts

Moe Bass
9,091
0
Maine
Not bad for two 10's - lol @ my buddy Mike who is filming.

Finished the box and installed it at my job the day before and had no test time what-so-ever.



Have a dash run as well if I can find it.

Real glad I did not sell these off to fund some other projects!!

Some pix

IMG_20140602_221355_zps90d336c0.jpg


IMG_20140606_124336_zps360577e3.jpg


IMG_20140606_190833_zps13ffc349.jpg


 
I actually put this on as a side show to a car show, and a large amount of the vehicles that came through the lanes were peaking at 55+hz on my tone sweep... I was pretty shocked. These people need a properly built and tuned box to get out of the 130s like I was seeing.

 
Thx. Going to try shortening the ports and see if that helps any. Also going to try and put both amps on a single 10 and see if I can manage a 150 with one 10.

 
I remember when I was at shows, guy terry Brock's was pulling good numbers with a design kinda like this. Def impressive for 2 10's.

 
I met Terry in MD at SLAP National Championships, and he is lending some advice on a nasty three 12 box for my crx that a friend is assisting me with //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 
shortened the ports, hope to see a small gain doing that. getting another 100ah battery to throw in as well, may try to burp @ .25 if my cohones are large enough

 
shortened the ports, went down to a 151.6 at the glass. made the ports quite a bit longer and went waaaaaaaaaay down to a 149.9. put ports back to standard size that I started with and right back to a 152.3...

tried burping @ .25 but the amps went craycray on me so that wont be happening.

didnt gain anything by adding the other battery as far as # on the meter, but seem to have another .4-.5v compared to just the batcap.

 
I've polished this turd as much as I can, time to do a few last minute tests and then it's the big Sanford Sound Bikini Car Wash/SPL show on Sunday....

The white really pops b/c it was a bit wet still, but I think it came out ok

sundownfi_zps6d4329e0.jpg


 
I've heard of a theoretical good gain just by removing the rear panels and perhaps including some dynamat to cover the gaping access holes, so the gut job begins.

gut3_zps4c85d761.jpg


gut2_zps4584e16b.jpg


gut1_zps7168df66.jpg


 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

Similar threads

Don't get me wrong I've built a few boxes myself and I love doing it and it would've been preferred. But I now live in a one bed room apartment...
42
9K
I would face the port and sub back. Even if you got a soft top, the rear gate will serve as a loading wall. I looked at the specs for the 10w6v3...
3
2K
Just trim strands until it fits. Then put some heat shrink or electrical tape on it.
104
11K

About this thread

CRXBMPN

5,000+ posts
Moe Bass
Thread starter
CRXBMPN
Joined
Location
Maine
Start date
Participants
Who Replied
Replies
29
Views
2,648
Last reply date
Last reply from
CRXBMPN
all out.jpg

Popwarhomie

    Jun 2, 2024
  • 0
  • 0
all out.jpg

Popwarhomie

    Jun 2, 2024
  • 0
  • 0

New threads

Top