Bamaboy's 04 Explorer Build 4 15s Wall...RF / Hertz

[bamaboy 5,000+ posts]

not sure...thats what it is, there is a few inches before you get to the back seat wasted amd enough room behind for the group 31s and more room before you hit the back gate

room up top and in front, but the back slopes down so had to angle the box to fit, but had to make it wider to get same airspace as bottom box

 

[taintedplay 10+ year member]

hmm. sounds good though. im thinking of doing a backup camera, how did you set yours up? and did you just leave the back windows? (not on the trunk)

 

[bamaboy 5,000+ posts]

never put the backup camera on and they eventually needed the one i had to do an install so i gave it back, will pick one up now since i have the new unit

sanyo has a new backup camera that looks cool, it has a processing unit that has a few options, it can take away the fisheye lens look of back up cameras and it will give you a birds eye view of what your doing with just the one camera, also if you mount it off center it has a way of centering the image up somehow, but expensive i think retail is 299$ now i just need to get them to order one for cheap //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

back windows? im confused what your asking

 

[taintedplay 10+ year member]

well on my expedition, the very back windows that would normally be beside the 3rd row seats open out a little bit in the back. well on 1200watts they vibrate like crazy. did you just like caulk yours shut or did you replace them or something? just so they wouldent rattle or is that not a problem for you

 

[GMCJimmyslt2000 10+ year member]

explorers don t have that ^^^

 

[bamaboy 5,000+ posts]

word^

 

[GAM3OVR 5,000+ posts]

Looks cool Mang, I'm gettin ready to start on my Audio here pretty soon too.

 

[taintedplay 10+ year member]

explorers don t have that ^^^

oh ok. ill just caulk mine shut i guess.

 

[Goldtaz1 10+ year member]

yea im ready to get it installed, probably tonight
so you finally cleaned out of audio in the yeller car?

Yep. Work on the Tahoe will hopefully begin soon if folks keep getting boxes built. I've got subs, I just need amps, batts, and alts.

 

[bamaboy 5,000+ posts]

everything taken out, got the bluetooth mic ran, both ipod and usb cable ran, harness is wired, Now only one thing holding me up, the brain unit for the flip-out was behind the golve box, thats where the RCA's plugged in, now they dont reach, im short about a foot and a half //content.invisioncic.com/y282845/emoticons/mad.gif.c18f003ab0ef8a0d9c27ca78d77a6392.gif

so im going to run by work and grab some short ones when i head to school in a bit, so i guess it will be tonight when im done

plugged it in to make sure it wouldnt blow up and everything works great, just need those dang rca's

Yep. Work on the Tahoe will hopefully begin soon if folks keep getting boxes built. I've got subs, I just need amps, batts, and alts.

well you got the easy part out of the way //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 

[bamaboy 5,000+ posts]

pics when i finished what i could a bit ago







what came out...ratnest of wires

 

[schrummy 10+ year member]

have you finished the back panel yet???

 

[DDbump 10+ year member]

those two seperate boxes?

 

[bamaboy 5,000+ posts]

have you finished the back panel yet???

nah, was going to fiberglass it but with cost of resin and amount of time to do it, just wasnt that important to me, im just gonna leave it like it is

those two seperate boxes?

yes and no, its 2 seperate boxes built, but they are common chamber-ish, holes cut into them and bolted together since the top box is a tad bit smaller than the bottom

 

[taintedplay 10+ year member]

how did you make the front beauty panel?

oh and also, i must say, you are my inspiration into doing my own wall