Free Box designs.

[rcnshoe 10+ year member]

2001 Nissan Maxima12" Fi Q w/ BP Power Option D2

Max External Dimensions

D X W X H

16" X 30" X 15"

Double Baffled

Tuned to 32Hz with single slot port

I would suggest around 2.25-2.5 cubes net with 28 square inches of port, but it looks to me like you need no suggestions. So please if you think you have a better idea, go with it.

Thanks in advance, anything is greatly appreciated

3.06^3 w/o port @ 32hz

 

[rcnshoe 10+ year member]

Thanks!
I still need dimensions on my slot ports *internal*... For the Fi Q 15"

Sorry about that. Recheck the picture on the first page. Reuploaded with dimensions

 

[ArrizX 10+ year member]

hook me up with a large sealed enclouser for two tc-7 10's (not sure how many cubes to run that at)

then also a ported box with precision ports.

i have two 13'' long 3'' diamater ports for each sub. i was thinking something like 34long 15 high and 15deep

figure something out please.

 

[rcnshoe 10+ year member]

2 12" memphis m3s 40"W x 18"H x 18.5"D tuned to 32hz center port. whats the donating rate these days?
thanks

Any donation is good! Whatever you think some of the 3d designs take about 30mins to 4hours.

6.256^3 w/o port at 32hz lots of port area!

 

[rcnshoe 10+ year member]

2 pioneer 12" 5000spl , w 46 x h 17.5 x d ( up to 22 ) , sub would be mounted in the 17.5" section, tuned@35 seperate chamber for each sub if its possible

thanks alot

ps

using 1" mdf all around

each chamber is 3.85^3 @35hz 1" MDF

 

[NissanKicker 10+ year member]

I need 3 designs please..... If possible.

I have 4 12" Eclipse SW7200 Series Subs...

.... First design will be (2) 12s Ported....

Max Dimension: 42"L x 14"H x 24"D

.... Design #2 is for (3) 12s Ported.....

Max Dimension: 41"L x 15"H x 24"D

..... Design #3 is for (4) 12s Ported.....

Max Dimensions: 36"L x 13"H x ??"D

( There is a 17"H x 22"L opening in the middle that leds into the cab... Use that for more airspace - Located dead center/middle of the trunk - My backseat stays down at all times )

Thanks in Advance!

 

[rcnshoe 10+ year member]

How about...
Dayton RSS265HF-4 10" Sub

Sub must be in Down firing config, flush mounted....using a slot port that goes out the top (out one of the sides, doesn't matter)...

the actual box must be a 12" x 12" (picture a standing rectangle)... but the height can be as high as needed to fulfill the requirements of the box...

Tuned to 20hz....

edit; 3/4" MDF...will be used..

Your box gives me headaches on building it. Also designing it.

1.875^3 w/o port @ 20hz

Bottom

Top

 

[nofriends46 10+ year member]

The design is still the same on the 1st page....

*waiting for you do re-image on the interntal slot dimensions*

Fi Q 15" Vented enclosure...

Donations will be sent, once i complete the enclosure!*

 

[rcnshoe 10+ year member]

The design is still the same on the 1st page....
*waiting for you do re-image on the interntal slot dimensions*

Fi Q 15" Vented enclosure...

Donations will be sent, once i complete the enclosure!*

 

[nofriends46 10+ year member]

Just wanna make sure, all the cuts, i need the add .75"?

Or its already added with the dimensions...

Width of the box is 34", the cut out is 34" 3/4....

 

[rcnshoe 10+ year member]

Me = ZZZZZZZZZZZzzzzz.... Need to work on my jetta tomorrow if it's not raining. I do some more boxes tomorrow don't worry =). Still no donations //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif:crap:

 

[rcnshoe 10+ year member]

Just wanna make sure, all the cuts, i need the add .75"?Or its already added with the dimensions...

Width of the box is 34", the cut out is 34" 3/4....

All the sides are measured in 3/4 MDF 34" is the width =)

I always add the 3/4 measurements into the box design or 1" or 1/2" Depends on the person but i always do 3/4 unless the customer wants something different.

 

[OoMesKoO 10+ year member]

Here's one for ya!

48"w x 24"h x 14.5d

Subs up, port back. Tuned to 33hz. 4 10" Power hx2s in a tahoe.

You are teh manz!!!1!1

 

[Punk In Drublic 10+ year member]

Hey rcnshoe your designs look rad.. could you make one with a double baffle for my 13W3v3-4?

Max dimensions are 14.5H x 28W x no more than like 27D

JL recommends 2.25^3 @ 27 hz, but the box on their site is too tall for my trunk (96 Nissan Maxima)

 

[mike11202 10+ year member]

Me = ZZZZZZZZZZZzzzzz.... Need to work on my jetta tomorrow if it's not raining. I do some more boxes tomorrow don't worry =). Still no donations //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif:crap:

//content.invisioncic.com/y282845/emoticons/wow.gif.23d729408e9177caa2a0ed6a2ba6588e.gif Come on guys he's doing all this great work for you and no ones given him any donations???