Using All-thread as bracing?

[bunkerking09 10+ year member]

So i'm literally sitting in my garage and waiting for a response on this...

How do you use all-thread as bracing? Just make the hole slightly smaller (it's 3/8") and then thread it though with nuts and washers on the inside and outside?

Get me a quick response and I might even make a build log by the end of the week //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Click to read more...

 

[duece212 5,000+ posts]

correct, drill the hole large enough for the allthread to barely fit through, run a washer and nut up on the inside and outside, seal it with some silicone and you are good to go. Might use some loctite

 

[IDSkoT 5,000+ posts]

Anyone with a brain can figure this out.

 

[bunkerking09 10+ year member]

Anyone with a brain can figure this out.

Always such a hater, just thought I would double check before I ruin a box.

I apologize.

 

[IDSkoT 5,000+ posts]

Always such a hater, just thought I would double check before I ruin a box.
I apologize.

Stupid questions deserve stupid answers.

How else are you supposed to do it? With hopes and dreams?

 

[bunkerking09 10+ year member]

Stupid questions deserve stupid answers.
How else are you supposed to do it? With hopes and dreams?

Didn't know if you literally threaded it through or something of the like.

I'm really starting to think your mom doesn't love you.

 

[gotparts90 10+ year member]

for a cleaner look use a carriage bolt on the visible side and join with a coupling. you can even set in in and fill over and wont even see it after paint/carpet. to use 2 carriage bolts you need a reverse thread one and a turnbuckle with jam nuts.

 

[IDSkoT 5,000+ posts]

Didn't know if you literally threaded it through or something of the like.
I'm really starting to think your mom doesn't love you.

You're a cool guy! I see what you did there! Yo-- haha //content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif

Oh, wait. That has no bearing on the fact that I think dumb questions should be asked.

 

[Pop da Hatch 10+ year member]

git r done bunker.

 

[bunkerking09 10+ year member]

git r done bunker.

Working on it //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

DP's inverted anyone? //content.invisioncic.com/y282845/emoticons/veryhappy.gif.fec4fed33b4a1279cf10bdd45a039dae.gif:veryhapp:

 

[jmiller0526 10+ year member]

You're a cool guy! I see what you did there! Yo-- haha //content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif
Oh, wait. That has no bearing on the fact that I think dumb questions should be asked.

//content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif

 

[iamamp3pimp 5,000+ posts]

Working on it //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif
DP's inverted anyone? //content.invisioncic.com/y282845/emoticons/veryhappy.gif.fec4fed33b4a1279cf10bdd45a039dae.gif:veryhapp:

you tell me?

they sure will be inverted in here...

 

[snb778 5,000+ posts]

Stupid questions deserve stupid answers.
How else are you supposed to do it? With hopes and dreams?

for a cleaner look use a carriage bolt on the visible side and join with a coupling. you can even set in in and fill over and wont even see it after paint/carpet. to use 2 carriage bolts you need a reverse thread one and a turnbuckle with jam nuts.

to IDSKOT...... so is everyone supposed to know what all those hardware parts are also.... i'd bet you don't even know what all those are

 

[snb778 5,000+ posts]

You're a cool guy! I see what you did there! Yo-- haha //content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif
Oh, wait. That has no bearing on the fact that I think dumb questions should be asked.

self PWNT

 

[gotparts90 10+ year member]

**** you all we are here to help each other.