Single 10 for daily SPL?

[bunkerking09 10+ year member]

Its gotta be loud as ****, sound good playing music (daily), and its only gonna be a single 10. Those aren't realistic goals for you imo.

ok, so then what would you use for SB1? The limit is (2) 10's, so what would you use in that case?

 

[mossberg385t 10+ year member]

TREO Engineering | SSp Series Subwoofers

treo SSP, the VC can handle 500 °F which is why the brace is there because the slugs get hot and melt the glue, its rated at 1krms however due to the VC design it can take a hell of A LOT more

 

[Slo_Ride 5,000+ posts]

Sundown Nightshade v.2 10"

Nightshade v.2 Teaser Picture - SSA Car Audio Forum

 

[tekk45 10+ year member]

Image Dynamics IDMAX. Killer SQ, capable of getting real loud.

 

[bunkerking09 10+ year member]

Sundown Nightshade v.2 10"
Nightshade v.2 Teaser Picture - SSA Car Audio Forum

will they be making that in a 10? I kind of doubt it...

 

[Slo_Ride 5,000+ posts]

He will. Gotta read the link.

 

[bunkerking09 10+ year member]

He will. Gotta read the link.

not a member on SSA, i'll just email jacob.

 

[Slo_Ride 5,000+ posts]

not a member on SSA, i'll just email jacob.

The NS v.2 is available. He said he may do some special order 10"s.

This of a NS v.2 15" not a 10" but...

(Quoted from Jacob Fuller)

Here are some T/S from the 15" D1 that I built for myself with 3 Hard spiders (stock stiffness):

RE: 2.09 ohms (D1 series)

Fs: 32.16 Hz

Qes: 0.48

Qms: 12.04

Qts: 0.46

Le: 2.86 mH

Vas: 47.05 L

BL: 20.07 NA

Cms: 53.44 uM/N

Mms: 457 g

The above with a very short break-in period.

After numerous 10,000 watt burps :

RE: 1.98 ohms (D1 series)

Fs: 31.78 Hz

Qes: 0.448

Qms: 12.20

Qts: 0.432

Le: 2.80 mH

Vas: 50.64 L

BL: 19.59 NA

Cms: 57.52 uM/N

Mms: 435 g

Spider seems quite stable in compliance after a tremendous beating -- of course we knew that from the v.1 Nightshade

 

[bunkerking09 10+ year member]

i joined just to read it haha.

seems like a well built sub, but i wouldn't expect any less.

It looks like it won't be available for a bit longer, which would be perfect timing for me.

 

[DammitJames 10+ year member]

apx 10? i ran one to 3 daily thrown 3kw rms at a single one before...

 

[O.G. D-Wet 10+ year member]

TREO Engineering | SSp Series Subwoofers
treo SSP, the VC can handle 500 °F which is why the brace is there because the slugs get hot and melt the glue, its rated at 1krms however due to the VC design it can take a hell of A LOT more

What are Treo's prices like? Always looked at them but idk anything about them cept they're sexy

apx 10? i ran one to 3 daily thrown 3kw rms at a single one before...

Same question^^^ what do they go for new/used?

 

[bunkerking09 10+ year member]

i've seen some APX 10's on 3k before, they were impressive.

 

[audioholic 5,000+ posts]

ok, so then what would you use for SB1? The limit is (2) 10's, so what would you use in that case?

You said this was a daily system, not competition. If you can run two 10's why are you wanting to do one?

And my point was you are asking a lot for a single 10, given the compromises needed to expect a competitive level of output.

 

[SPLaudio 5,000+ posts]

cause it is fun to run a single 10" and see what can be done is why i did it. why ya need a pair? in a good install he could do low 140s and be tuned to 32hz...

 

[bunkerking09 10+ year member]

i would pray to God I can do better than low 140's