04 Sentra SE-R amateur/budget SQ build

[Extreme SE-R 10+ year member]

Deck: ////Alpine 9887 attached to a Ipod 60Gig

Front: Polk Audio Momo MMC6500 6.5 Components 4ohm

Recomended Power: 125 RMS 250 Max

Running at: 135+RMS

Rear: Polk Audio db650 6.5 Coaxial 4ohms

Recomended Power: 60 RMS 180 Max

Running at: Thinkin bout 70 to 100RMS..wat evr sounds best

Sub: Elemental Design 13Kv2 Dual 2ohms running@1 Ohm

Recomended Power: 500 RMS Max..?

Running at 750+RMS@ 1ohm

Sub Enclosure 1.5 Cubic Feet Channel Port @30Hz Built to Elemental Design Spec

Amp: Elemental Design Nine.5 (5 channel)

Elemental Designs NINe.5 Test Report

13.2v Bench.

Tested at 1khz

4 Channel @ 4 ohm- 23 volts - 132 watts

4 channel @ 2 ohm- 22 volts - 242 watts

2 channel @ 4 ohm- 23 volts - 132 watts

2 channel @ 2 ohm- 22 volts - 242 watts

Tested at 50hz

Sub @ 4- 35.5volts - 315 watts

Sub @ 2- 31 volts - 480 watts

Sub @ 1- 28 volts - 784 watts

Wire:

* RCA

Monster Cable XLN 401

Monster Cable XLN 302

* Power Wire

KunKonceptz 0AWG 5140 strands!!!

* Fuse/Block

Stinger 200A /Generic Block

* Speaker Wire

Rockford Fosgate Speaker wire 16AWG

Rockford Fosgate Sub Wire 12AWG

Noise Control

* Dynamat Extreme about 4-5 sheets...Surprisingly the Sentra had OEM Deading aswell

The Car!!!

my friend asad aka "that boy asad" helped out alot so i start the pic log with him

deading then spacers

then some more deading ovr the spacer just incase..

then finally the momo 6.5" mid bass

Sorry for the camera phone picture...(lost my digital camera for a while)..

door with momo grill on the panel.

Silk/Polymer tweeter

Finished driver side door Panel

RIght Door

Click to read more...

 

[Extreme SE-R 10+ year member]

The wires n accessory for the build

​

Monster Cable XLN 401

Monster Cable XLN 302KunKonceptz 0AWG 5140 strands!!!

Stinger 200A /Generic Block

Rockford Fosgate Speaker wire 16AWG

Rockford Fosgate Sub Wire 12AWG

Monster 300 Crimpless Ring Terminals

For the rear fill i ran out of wire..so this being a budget build/BROKE... had to use old RCAs as Speaker wire...

(step by step process starting from the left)

RCAs going to the deck - Rapped heavily with Electric tape to ensure clarity/static prevention

Wiring going to the trunk

After sorting

Unsorted wires in the trunk

after sorting

 

[Extreme SE-R 10+ year member]

Amp Rack/Trunk

​

The Work Station

The car and the "hairy Dude" Aka asad

http://farm4.static.flickr.com/3250/3039484114_c683e1384f_b.jpg

The amp and the Dark Dude...Aka.me

Channel Port Box built by Stereo EFX

Rear deck B4 Deading

 

[Extreme SE-R 10+ year member]

Elemental Design Nine.5

 

[JrVtecAccord 10+ year member]

That last pic isn' the final touches is it? I hope not, if it is, work on the cosmetics and you should be good.

I didn't see any fans, I am not sure if that amp produces a lot heat, but that is something I would look at, especially in this Texas heat in summer. Also, you need more dynamat in the doors, try to fully seal them f-ers, yes I know it is very time consuming, but the payoff is great.

 

[path2spl 10+ year member]

nice camera. nice build, i would of done with out the wall though or built a face plate

 

[Extreme SE-R 10+ year member]

That last pic isn' the final touches is it? I hope not, if it is, work on the cosmetics and you should be good.
I didn't see any fans, I am not sure if that amp produces a lot heat, but that is something I would look at, especially in this Texas heat in summer. Also, you need more dynamat in the doors, try to fully seal them f-ers, yes I know it is very time consuming, but the payoff is great.

No..lol its not finished yet...i need to buy carpet...ima redo the hole thing with just one piece of carpet on the wall..and one on the floor...

i already have fans left ovr from my computer...but i need to buy volt regulators...i can't remember wat the name is for it...but need consitent 12V...its cheap but...kinda burned out on this project at the moment..plus got other things that needs to b done..but i definitely keep u guys posted. also thinkin bout doing some kind of light for the amp rack

 

[ahillworks 10+ year member]

Good setup! Yeah I agree with redoing that wall and bottom. Use one board for both. It will look way better. But over all you made me miss my Sentra thanks! lol. Nice build man keep us posted. //content.invisioncic.com/y282845/emoticons/cool.gif.3bcaf8f141236c00f8044d07150e34f7.gif

 

[endofdays89 5,000+ posts]

the boards you put back their are too noticable, i would just stick with the sub box and take the other pieces of carpeted mdf out of their.

 

[Extreme SE-R 10+ year member]

nice camera. nice build, i would of done with out the wall though or built a face plate

Thanks..the camera is OLD!!! lol its a 4MP olympus IR-500..

Im not sure wat u ment by face plate...but...im guess like a single peace of wood instead of the 3 piece around the sub box.....if so.. i didn't/couldn't wanna do that cause...the only real tool i had was a Circular saw!!! and a chisel!! lol...it was hell cutting the MDF to match the corners of trunk..so.. i can only do so much..i do plan on getting more electric tools though

 

[smiley2186 10+ year member]

very nice build love the amp.

 

[B_Campbell 10+ year member]

Nice, that's one hell of a camera you have.

 

[Extreme SE-R 10+ year member]

Nice, that's one hell of a camera you have.

To be honest...its not all the camera..using natural light and steady hand is the key!!!..Using Flash is Gay!! i bet every one has a bad ass like...15,000MP camera...LOL...mean while i have a 3-4 year old 4 MP olympus...

 

[shahir 10+ year member]

i think it came along pretty well... even though we had not planned anything out, we did not have the right tools, and this was our first time doing something like this!!!

 

[standbackimapro 10+ year member]

Put some kind of illumination under that plexi, itll look sweet