Walling off my car, part 2 (the pics thus far)

[Kenny Pollock 10+ year member]

Take 2 > Take 1

Better design... it was actually designed pretty much ONLY with ease of build in mind //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif a lot less complications.

Cuts will be even, equal, clean, exact... going to have a local cabinet shop do them.

I will be buying a gallon of Titebond II and using it instead of the Liquid Nails.

We now have "wall building experience" so this should go a little bit faster and smoother.

 

[tommyk90 5,000+ posts]

Take 2 > Take 1
Better design... it was actually designed pretty much ONLY with ease of build in mind //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif a lot less complications.

Cuts will be even, equal, clean, exact... going to have a local cabinet shop do them.

I will be buying a gallon of Titebond II and using it instead of the Liquid Nails.

We now have "wall building experience" so this should go a little bit faster and smoother.

//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 

[PowerNaudio 10+ year member]

i think there is going to be a weak point rigth in between the subs.i think youll be better off having one sub higher then the other.

 

[saywhat? 5,000+ posts]

I know nothing, absolutely nothing.

 

[saywhat? 5,000+ posts]

i think there is going to be a weak point rigth in between the subs.i think youll be better off having one sub higher then the other.

should be fine. have you seen Meades honda? even closer.

 

[squeak12 10+ year member]

If you want to brace it run some threaded rod right there, or if you want to take the chance of turbulance put a 2x4 on the inside if it will fit.

 

[tommyk90 5,000+ posts]

If you want to brace it run some threaded rod right there, or if you want to take the chance of turbulance put a 2x4 on the inside if it will fit.

Actually, if you think about it, a 2x4 there would decrease turbulence. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

The subs will be forcing air against that 2x4 and out in to the enclosure versus pushing against one another.

But shhh, you didn't hear that from me. //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

And, if you wanted to make it even awesomer, you could put some angles along where that 2x4 is to make the airflow even smoother. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[PowerNaudio 10+ year member]

should be fine. have you seen Meades honda? even closer.

no i havent see the honda. im just pointing it out. i rather be safe then sorry, if you think having that little bit of meat in between if ok. hey go for it. it will most likly work. but it will still be a weak point on the wall.

 

[saywhat? 5,000+ posts]

the airspace is pretty tight to fit that setup, but we should be able to work it well enough where it shouldnt bother much at all

 

[saywhat? 5,000+ posts]

no i havent see the honda. im just pointing it out. i rather be safe then sorry, if you think having that little bit of meat in between if ok. hey go for it. it will most likly work. but it will still be a weak point on the wall.

not saying your wrong lol... you and me both know that we both have a handle on this box deal. It will be supported sufficiently inside and out.

 

[PowerNaudio 10+ year member]

i didnt mean to be pushy i just like to design so there are no posible flaws. if there could be, lets say i over build. lol

but it is looking pretty good.

 

[Kenny Pollock 10+ year member]

I think threaded rod near where the subs are through the box will help with that... and 45 degree angles will help a little with structural support too. I really like the idea of surrounding the wall in 2x4s //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[PowerNaudio 10+ year member]

i think that would be way more then overkill. how about just putting 2 x 4 like every 6" from each other. that will give you close to the same support, but will not weight it down as much.

 

[Kenny Pollock 10+ year member]

True... was just thinking though, 2x4s screwed/glued into other 2x4s screwed/glued into the wall... that would take care of any side flexin' //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[PowerNaudio 10+ year member]

ha ha. that's so true. you could really call that bulletproof