Need a Positive battery Terminal

10 Xscorpion 0 Gauge Ring Terminal Crimp 1 0 Platinum 5 Blue 5 Silver Terminals | eBay

 

---------- Post added at 02:53 PM ---------- Previous post was at 02:52 PM ----------

 

You can go to AutoZone/Orileys/HomeDepot to get those Cheaply,Take the Screw with you,and find the ring terminal you want(4/2/0ga)and find the Outlet for it to fit snugg..Think I bought 3/8,or 5/16.Copper ring terminals,to crimp,then use a punch to make sure they stay tight,and heat shrink them/can buy hshrink cheaply at HomeDepot/Lowes in electrical section as well,I use pure copper connection ring terminals.//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Do you have a punch?

 
10 Xscorpion 0 Gauge Ring Terminal Crimp 1 0 Platinum 5 Blue 5 Silver Terminals | eBay 

---------- Post added at 02:53 PM ---------- Previous post was at 02:52 PM ----------

 

Do you have a punch?
Old school style/several,,Lay down on garage floor, and use hammer and punch,I do 3 per terminal,in triangle mode,One at top, and one on each side..that joker will never come loose.You can get a punch(hammer punch) for like $3,or use a 16 penny nail ,and do it on a 2x4 to keep the nail end from flattening out

 
Old school style/several,,Lay down on garage floor, and use hammer and punch,I do 3 per terminal,in triangle mode,One at top, and one on each side..that joker will never come loose.You can get a punch(hammer punch) for like $3,or use a 16 penny nail ,and do it on a 2x4 to keep the nail end from flattening out
Sweet, I need to get one. They can be had at Home Depot I'm guessing?

 
I like that there,esp. if doing for buisness work/daily,but $3 bucks for one at HomeDepot/Lowes works well with a hammer,on an Anvil/bench vise/concrete floor.Nice crimper though.I use copper ring terminals because they are softer than the metal/zinc terminals, and crimp alot easier/hold much better as well
http://www.caraudio.com/forums/dc-creations/548842-copper-ring-terminals.html

that crimper makes thing so easily i tin my wires before crimping always

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

Similar threads

I would tend to blame the amp more than tbe sub if all wiring checks out. Skar is known to be on the finicky side when abused (not enough power...
9
121
How I would approach it is install your new amplifier and start using it. Install a voltage gauge and if you see your voltage lowering then add...
4
186
While most Asian and African markets will identify Honda's small hatchback as the Jazz model, most Western regions will know the same model as the...
2
140
The Kappa's have a high sensitivity rating of 93 db so the X802-5 would be fine. A good high sensitivity 8" sub in a properly sized box would fit...
2
492

About this thread

sbelew

10+ year member
Senior VIP Member
Thread starter
sbelew
Joined
Location
New Port Richey, FL
Start date
Participants
Who Replied
Replies
37
Views
3,504
Last reply date
Last reply from
sbelew
20240519_201344.jpg

audiobaun

    May 19, 2024
  • 0
  • 0
Screenshot_20240519-213549.png

1aespinoza

    May 19, 2024
  • 0
  • 0

New threads

Top