MM4000.1 1 ohm stable?

[bonesninja 5,000+ posts]

Ahhh....it'll out the amp trying to see .5 and prolly not rise high enough to play daily
You could try wiring in series than hooking up mono and be at 2ohm be decent power....or one ohm stereo for 2000watts

if you wire a dvc 2 ohm sub in series..you get 4 ohms......no matter what you do from this point as far as hooking the positive and negative wire to the amp....it is still 4 ohms no matter what

4ohms mono would be 2ohm actual

this is incorrect...4 ohms is 4 ohms no matter what. if there is one positve lead and one negative lead hooked to the amp...you cannot change the load load simply by changing what terminals on the amp you connect those 2 wires to.

Well hard to explain....but why do you think the rating is 4000x1@2ohm mono and 2000x2@1ohm stereo
Or that its only 2ohm stable mono but 1ohm in stereo

this part i understand fully

 

[Seattle206 10+ year member]

the ? remains...will it do 1 ohm mono for daily use..? safely? im not about to start blowin amps

 

[bonesninja 5,000+ posts]

only time ur amp will see half the ohm loadage is when u bride the amp/ run it mono that means 1 positive on left side of the amp and negative on the right side of the amp u get the point. so yes if u had an single 4 ohm vc sub and wired it to the amp mono then yes each side of the amp will see an 2 ohm load. like i said ive heard these amp sweet spot is around 3.3 ohms so depending on box and port size. id keep the Dual 2 sub and wire it @ 4ohms mono. maybe ur imp rise wont be soooooooooo bad and u get around the sweet spot 3 ohms

thats the key point here....each side....so 4 ohms mono is not 2 actual....its 2 ohms per side.

 

[tooloud4tv 10+ year member]

basically same thing we sayn/ or tryn 2 say

 

[bonesninja 5,000+ posts]

ok we're all good here

 

[Skip01 5,000+ posts]

basically same thing we sayn/ or tryn 2 say

Yeh..its hard to understand if you never had one....haha.....i cant explain it better really

Its not a mono amp...thats the biggest key....i know mono amps have 2 sets of terminals to but they are internally strapped so it doesnt matter...that would be what ur thinking

This is not internally strapped....its 2 separate 2000 watt amps inside

 

[Seattle206 10+ year member]

the ? remains...will it do 1 ohm mono for daily use..? safely? im not about to start blowin amps

???

 

[tooloud4tv 10+ year member]

well i told u that ive been running the amp 1 ohm mono for an while now with no problems. oh yea and thats with AN SUCKY electrical. only problem i have is it kicks into protect from time to time. but thats only because of low voltage.

 

[Skip01 5,000+ posts]

???

Read that thread i posted and this one:

http://audioforum.termpro.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=20;t=013563;p=0

Me personally i wouldnt run it at .5 ohm....you lose alot of efficiency and only minimal gains, if any really

 

[Seattle206 10+ year member]

ya i read it...but i dont feel like reading the whole 6 pages..but if u would be so kind as to simply throw me an answer....1 ohm mono for daily..yes/no?

 

[Skip01 5,000+ posts]

ya i read it...but i dont feel like reading the whole 6 pages..but if u would be so kind as to simply throw me an answer....1 ohm mono for daily..yes/no?

Well if ya dont wanna read ya dont wanna learn......good luck

 

[Seattle206 10+ year member]

Well if ya dont wanna read ya dont wanna learn......good luck

mi amigo! that hurts me deep...after all we've been through?//content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif

 

[tooloud4tv 10+ year member]

Seattle206 NO! is the answer

 

[Seattle206 10+ year member]

Seattle206 NO! is the answer

ok thanks..

 

[tooloud4tv 10+ year member]

what type electrical u have for the amp currently?