jl audio 1000/1 v2

[rick265 10+ year member]

I have two jl w6 v2's in jl box that was powered by a jl A1400 amp but i sold it to my friend because it wasn't powerful enough so I ordered a jl 1000/1 v2 amp will this new amp draw be too much for my cars electrical system to handle?

Click to read more...

 

[wheeler8921 10+ year member]

yes, sell it to my and buy my dd m1a 1200rms @ 1ohm.

 

[budahbuddy803 10+ year member]

haha well what kind of car do you have? have you done any electrical upgrades?

 

[rick265 10+ year member]

2001 saturn no electrical upgrades my jl A1400 didn't cause the head lights to dim but it was 500 rms at 2 ohms

 

[valter 10+ year member]

You'll be fine, it is more efficient and has more internal capacitance.

 

[civic92]

hey guys help me on this....i got 2 13w7 and two 1000/1 v2 with a 300/4 v2 and a set of vr600 csi jl component with a pioneer head unit p6900ub. i wanna know do i have to upgrade electrical or anything else to have the full potential of the system...i want it to be loud *** hell...let me know what else i need...thanks.

 

[MrDGP04TL]

hey guys i got 2 12" W3's 4 ohms and i have a kicker KX25001

I was wondering if i crank my music in my which is 40 what wuld b the best wattage it be at

rms is 300 max peak is 600

any1 know?

 

[Fach 10+ year member]

hey guys i got 2 12" W3's 4 ohms and i have a kicker KX25001
I was wondering if i crank my music in my which is 40 what wuld b the best wattage it be at

rms is 300 max peak is 600

any1 know?

If you're wired at 4 ohms, or 1 ohm, either way its bad with a kx2500.1...that amp runs at 1500rms at 4 ohms and 2500 at 2 ohms. The 2 ohms doesn't apply to you. 750 rms would be going to each sub and conclusion, you're going to destroy the subs. Get a monoblock class d amp that does 600 rms x 1 at 4 ohms or a 2 channel 300 rms a piece (each channel) at 4 ohms. That's if your subs are wired to 4 ohms and not 1. Either way that amp is way too much power for those subs.

 

[nate757]

hey whats up i have a proble with my set up somewhere. i have 05 nissan maxima with JL1000/1v2 Class D Monoblock Subwoofer Amplifier, 2 12"JL w6/v2 and a Batcap 400 setup with entire trunk lined with extreme dynomat, yet when i turn the volume up all of the way base cuts out and the blue led lights up saying low voltage. do guys know how can i get rid of that so that it work properly again?

 

[mmouse57 10+ year member]

yeah get out a digi mmeter lol and test your self where the issue is coming from instead of asking us

 

[AudioFreak 10+ year member]

It might be because the amp only runs 1.5ohms-4ohms and your giving it a 1ohm load

 

[nate757]

how do i turn the load up on the amp?

 

[JDBoogie 10+ year member]

How do you have your subs wired?

go here (http://mobile.jlaudio.com/support_pages.php?page_id=161) and wire for a 4ohm load.

 

[LoggedOut 10+ year member]

wtf is happening in this thread? 3 threadjacks? all about the same shit? i smell trolls

 

[nate757]

How do you have your subs wired?
go here (http://mobile.jlaudio.com/support_pages.php?page_id=161) and wire for a 4ohm load.

hey thanks i'll be playing with it in the morning see how it goes.