Free Box designs.

[sl600 10+ year member]

each chamber is 3.85^3 @35hz 1" MDF

thanks alot for your help do appreciate it, i forgot to let you know that i will be

inverting the subs, that would changes the chambers volume, if its not to much to

ask can you redo the skitch,you could cut down on the deepth since the subs volume would be out of the count.

again thank you for your effort and help

 

[chinxtaboi 10+ year member]

i actually just sent in my donation of 8bucks. guess thats better than nothin. another request.

single 12" memphis m3 30"w x 14"h x 17"d tuned 32hz. slot ports on both sides. want the box to look symmetrical.

thanks

 

[rcnshoe 10+ year member]

thanks alot for your help do appreciate it, i forgot to let you know that i will beinverting the subs, that would changes the chambers volume, if its not to much to

ask can you redo the skitch,you could cut down on the deepth since the subs volume would be out of the count.

again thank you for your effort and help

The box ^3 is without sub displacement. So it wouldn't matter if you inverted the subs. But if you want i can re do the box.

 

[rcnshoe 10+ year member]

I'll be on tonight to do some more boxes.

 

[zukkaa]

one 12" Alpine type R in a single cab ford ranger.. there isnt much room. The sub magnet has to stick out backwards through the middle of the 2 seats. The front board has to be flush with the angle of the seats.( You have 10" on the bottom and 4" on the top) Im not sure if that makes sense?

Height 23"

Bottom width 10"

top width 4"

Length 53"

 

[trow100 10+ year member]

Just seeing if you could design one for me for a 9510g. DD recommends around 1.25-1.5 ported to 40hz so i would go with that. Tallest the box could be is 14 inches just to be on the safe side and 36 inches wide and 16 back to play with probably. Port and sub firing back.

 

[chinxtaboi 10+ year member]

Any donation is good! Whatever you think some of the 3d designs take about 30mins to 4hours.
6.256^3 w/o port at 32hz lots of port area!

now i see it i think id rather have a more rectangular port.. but no taller than the sub itself. so if you could adjust, thatd be koo

thanks

nvm.. if i just adjust the sides and keep the port area the same it would be the same as the original right?

 

[king ranch 5,000+ posts]

i have a request for 2 12's l7 ported i have bout 34 inches in lenght and 18 in width and 20-25 in height the only thing is the front of the box can only be about 14 inches wide and getting bigger towards the back of the box to 18 inches this is going to sit where the back center console is in a king ranch supercrew i am going to take out the console

thanks

 

[nofriends46 10+ year member]

All the sides are measured in 3/4 MDF 34" is the width =)
I always add the 3/4 measurements into the box design or 1" or 1/2" Depends on the person but i always do 3/4 unless the customer wants something different.

The box you design me, Reg Ported box 4.42^3 real @32hz

Is it before displacement or after displacement? For the FI Q 15". It might be to big, for the enclosure. If so, can you design another ported enclosure in the range of 3.5-4cf.

 

[sl600 10+ year member]

The box ^3 is without sub displacement. So it wouldn't matter if you inverted the subs. But if you want i can re do the box.

thanks for your quick respond, if its not to much to ask,can you redo the box with these dimentions ( since its going to be an inverted setup )

w 46 x h 17.5 x d 19 tuned@35

thank you for your help

 

[rcnshoe 10+ year member]

The box you design me, Reg Ported box 4.42^3 real @32hz
Is it before displacement or after displacement? For the FI Q 15". It might be to big, for the enclosure. If so, can you design another ported enclosure in the range of 3.5-4cf.

Calutate around 4.05^3 sub area

 

[morgans432 10+ year member]

http://www.imagedynamicsusa.com/pdf/Box%20designs%20for%20subs/2MAX12%202_3%2028%20hz%202%20chamber.pdf here is the design form the Image Dynamics website. It needs to be these specs please.

Donation will be sent very soon.

 

[bonesninja 5,000+ posts]

how about a 2.5 net with .3 total sub displacement tuned to 33htz single port centered on front, subs front mounted, 10" re sx's

http://www.reaudio.com/specs.html#sp_sx

max dimensions 48" wide x 14" high x 18" deep

 

[IonSQL 10+ year member]

Calutate around 4.05^3 sub area

Check your PM's...

 

[morgans432 10+ year member]

ttt for great designs