Recent content by ecbmxer

Yea, I saw it on Amazon. I'll probably go that route, but figured I'd check here to see if anybody had one to sell for less. Pretty much one of the only options to go active with a new receiver without spending huge cash on a Pioneer P99 or BitOne/MS8 type of processor. The one for the 9887...

Name? Clint B Location? Morgantown, WV Contact info? PM me Wanted to post this up on the off chance that somebody has an Alpine bluetooth module (KCE-400BT) and/or an Alpine Imprint module (PXA-H100). Since these just go behind the dash, it doesn't really matter if they're brand new or not...

So I haven't been into the car audio stuff for a while. I sold a 2005 Nissan Titan I had a while back with a nice audio setup. Now, I just bought a 2010 WRX and need to upgrade the system. I am trying to be minimally invasive here and not mount any subs/amps all over the floor, etc. Also I want...

amp is sold

I'm trying to sell my DLS Ultimate A5 3-channel amp. This is the nicest amp I've ever used and would work well in most front stage/subwoofer applications. It does 85Wx2 to the front and 300Wx1@4ohms, 500Wx1@2ohms, or 780Wx1@1ohm. It also comes with the bass control knob that you can mount under...

I finished the construction on my second box for a 2005 Nissan Titan KC. This time it is an upfiring design for 2 JL 10W3V2 subs and has about 0.8 ft^3 per side. I am trying to decide what to do for the finishing. I had the idea to put a single layer of fiberglass and resin down and then either...

How are the subs wired. Its either gonna be 9 ohms or 0.75 ohms. Either way is not gonna be good for the JL amps. They are made for 1-4ohms. The 0.75 will probably kill the amp over time and the 9 ohms you will get no power and probably more thermal noise in the system.

I kinda agree with you. I don't have the room to port them unfortunately. Unless I went with only 1 W3, but I would have no output then. I'm gonna go talk to the place I got them and see if they have some dual 4 ohm w3's I can try to see if it improves anything with more power.

OK, maybe I'll see if I can trade them for the dual 4 ohmers. Then I could have a 1 ohm total impedence and run 780W to them. I will not ditch the amp... ever. I love this DLS A5 amp. I will try more power though.

Hey guys, right now I have 2 JL 10W3V2 subs in a sealed box in my 2005 Nissan Titan kingcab. They are getting around 500W right now at 2 ohms and are each in around 0.5 ft^3. Now, I know they don't have much volume and I think thats part of the reason why I am not happy with the setup. They are...

I've done my install and I have a really bad case of engine whine. I am running a Pioneer DEH-P8MP HU and a DLS A5 amp powering a DLS MS6 component set up front and 2 JL 10W3V2 subs. I have a 2005 Nissan Titan king cab truck. I have the amp grounded on an existing ground point behind the rear...

Excelerater, now you got me thinking about trying to add another set of speakers. I have a set of DLS MS6 speakers in my Nissan Titan. I am running them with a DLS A5 amp. It can do 2 ohms to the comps. Would it work well to add another set of speakers in paralell with the comps? Wouldn't the...

Here are the pics of my sub box. Also, I just realized that I posted this in the speaker section. If a moderator wants to move this to general or the pics section, please do.

I've been working on putting together a system in my 05 Nissan Titan, and its almost finished. I have DLS MS6 components up front, and DLS 226 coaxial speakers in the rear. The rears are running off HU power and the fronts are going to be run off of a DLS A5 amp (85x2 + 500x1 @ 2 ohms). I have...

What settings are supposed to be inside my MS6 component crossover? On the case it just says "selectable tweeter level inside" and the same thing in the instructions. But then in the diagram in the instruction manual it shows another place for a jumper and a hi/low setting (crossover freq?). In...