::TESTED:: Audiopipe AP30001D

[basscort2009 5,000+ posts]

They dont know.....

i know i usually dont argue cuz its a losing battle. but all the true spl guys know. well even some of them dont. lol. my buddy is running 14k rms and 1 18 and its not fused once lol

 

[mgcauctions09 10+ year member]

yea but take all them out and whatch ur score go up about 2-5 tenths //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Actually to the volt meter it was the same so I dont see how my score would be better. I guess I have no loss due to 4 runs of positive and 4 runs of ground 2 of each per amp.

 

[mgcauctions09 10+ year member]

I agree, when it comes to competing, that is fine as you want every 1/10th you can get. As for a loud as F u c k daily driver fusing is the best option. Just add an extra run of 1/0 to make up for the loss. Thats what i did. Its a hell of alot cheaper adding 1 extra run of 1/0 then replacing vehicle,equipment or both.//content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[Annnarbor84 5,000+ posts]

Mine is daily tuned to 36hz, I have a few runs of negative and positive though also:laugh:

 

[Bobby322 10+ year member]

Can I wire it to 1 ohm and be fine?

 

[4OZGLOVES 10+ year member]

Can I wire it to 1 ohm and be fine?

do you have the electrical to back it up.

 

[timmoore718]

I may be new on "THIS" forum, but not on others, and I couldn't agree anymore with what you said. I just bought 2, and hope to hell that there at least "decent" Im not looking for quality like my VLX400/USA800 amps, but something to hold me over till I can afford 2 DAT2500.1's or 2 SAZ3500's or something. And with all i've been reading on the internetz, they should be just fine.

pics? //content.invisioncic.com/y282845/emoticons/yumyum.gif.0556df42231b304b9c995aefd13928a8.gif

 

[timmoore718]

Can I wire it to 1 ohm and be fine?

as previously said, the box matters a ton! I ran one of these with the same electrical at 1 ohm in two different boxes, one box worked, one didnt. if youre unsure on how to do a proper box, you could always find someone on these forums that does, or just up it to 2 ohms. gonna be louder of course at 1 ohm though

 

[Bobby322 10+ year member]

Well I have a D2 sub so I cant wire it to 2 ohm. its either 1 ohm or 4 ohm. I have a c&d battery in the back and I dont play it full tilt often. Hopefully I have a high imp rise.

 

[timmoore718]

Well I have a D2 sub so I cant wire it to 2 ohm. its either 1 ohm or 4 ohm. I have a c&d battery in the back and I dont play it full tilt often. Hopefully I have a high imp rise.

dam bro, with a stock alt and only that batt, good luck on 1 ohm even with the proper box //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif

 

[4OZGLOVES 10+ year member]

I would get another c&d before i tried it at 1 ohm

 

[Bobby322 10+ year member]

I put it on 1 ohm and it doesnt go into protect. I put my pos and neg speakers wires in seperate terminal things. I dont know if I should put them side by side or keep them the way they are. It doesnt hit hard at all, all my settings are messed up. What should I have the LFP, Subsonic, freq, etc. at? Im tuned to 32hz.

 

[basscort2009 5,000+ posts]

subsonic at like 30-35 lpf about half. gain at about a quarter pobly. freq about 60

 

[Bobby322 10+ year member]

do you know what the settings go up to? or is that just an estimate based on all amps?

 

[basscort2009 5,000+ posts]

estimate based on ur setup and box tuning