Need YOUR input.. 12" test session..

[lilmaniac2 5,000+ posts]

no need for them to be calibrated to each other b/c each vehicle will have a termlab used in it and solely in it.. this will keep variables down.. someone was asking for spl of the subs were gonna kill which could be done with the 4th tl for the truck

 

[bigbassman Premium Member]

Lucky.. squeak, pms..

Loyd L.

 

[ramos 5,000+ posts]

This is starting to sound like I'm gonna need a hard hat and flak jacket //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[Chevyaudio 5,000+ posts]

I have a question....dont know if its been asked...But how is the Enclosure situation going to work out. Will every sub be loaded into the same enclsure, or do you all in WV just have a forest of MDF behind yalls houses? If yall are building an enclosure for every driver...thats alot of building.

 

[Johnny Drama 5,000+ posts]

Speaking of what Chevy just said...

I'll donate the cost of a sheet of MDF for the cause. Loyd, let me know //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[ramos 5,000+ posts]

My idea would be to make a large sealed enclosure , then use blocks , or sand bags to make it smaller //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[Electrodynamic 10+ year member]

There will be a few enclosures to choose from, but I assume that most of the dual 12's will be loaded into Loyd's box. It is a very solid platform to work from - not too small and not too big.

 

[ramos 5,000+ posts]

One size fit's all if you build for the largest needed //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[JimJ 5,000+ posts]

I have boxes for the drivers that will like smaller boxes - 1.5cF ported for both single and dual moofers.

 

[ramos 5,000+ posts]

I'm sure we could find somebody to build something if we need it //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[lilmaniac2 5,000+ posts]

ramos i got me a new table saw begging to be used //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[denim 5,000+ posts]

stupid f'n wedding I do not want to go to is that weekend

 

grrrrrr

 

[bigbassman Premium Member]

hey guys.. for the enclosures.. here's what Im planning..

first off.. we'll be aiming for a .707 butterworth alignment sealed.. we'll stay with 15% of that for every woofer..

we'll be using data provided by the companies to achieve that design.. if no data is available.. they'll be derived from the woofer tester..

most 12" drivers call for between 1 and 1.5 cuft sealed... so we'll probably build a single 1.65 cuft box, and have several sandbags on hand to adjust..

ported.. we'll have a couple designs.. probably 1.8, 2.2, and 2.8 cuft tuned to around 30-32 hz..

Loyd L.

 

[bigbassman Premium Member]

mods.. please shut this thread down if you would..

THANKS EVERYONE FOR YOUR INPUT!!!!!!

Loyd L.

 

[bimma85 5,000+ posts]

ibtl //content.invisioncic.com/y282845/emoticons/woot.gif.aaa6090e619a97b6090d16dd863c5a69.gif//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif

Lloyd, is there gonna be a thread on roe to post...or just a locked one with all the info?