My Sub Box Finally Done !!

[Nascarfan 10+ year member]

Finally I had time to carpet my box, I think it turned out really well,the only think left it to cover up the screw holes with some carpet pieces. also I got carried away and decided to build an amp rack which is mostly done except the carpeting and the lid cut outs for the amp and plexiglass. Hope you like it.

Thanks Chris

http://home-and-garden.webshots.com/album/558525751Skftdr[/url]

[/img]

Click to read more...

 

[Immacomputer 10+ year member]

Looks pretty nice! Good job.

 

[60ndown 10+ year member]

there room there for 2 more subs,

post pics when there in //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[kickerlivinloud 10+ year member]

Looks good man!!

Spec's on the box??

Jon

 

[Nascarfan 10+ year member]

Thanks Guys, I just added a link to more pictures of the box being done.. yes there is room to grow in this box, currently I built it as a enclosure to hide my sealed box inside which is 1.25 cube ft per side. But I can easily remove that and use the enclosure when I decide to add more subs and another amp. You will see my almost finished amp rack in the pictures, the pics show the rack with out the lid on it, the lid will consist of 2 cutouts for my amps to show thru, and they will be under plexiglass flush mounted, then I will add some nice lighting to the whole project.

http://home-and-garden.webshots.com/album/558525751Skftdr[/url]

 

[9512ds 5,000+ posts]

woofers look photoshopped to me?

 

[mikey060 10+ year member]

they do too...i think its just the little bit of white that give that illusion

 

[Nascarfan 10+ year member]

click on the link below to see all the pictures, trust me they are not photo shopped

the only thing I did hide was the screw heads but you can see them in the other pictures, i had to use a rubber mallet to squeeze the carpeted face over the subs, it was a very tight fit.

]http://home-and-garden.webshots.com/album/558525751Skftdr

 

[azbass 5,000+ posts]

that pic looks photoshopped

 

[9512ds 5,000+ posts]

I mean i believe you...

it just really looks photoshopped

 

[RipDaJacka]

wut did you use to make it hug the fender wells? I like that clean fit look, I need a tip to keep the cut as close to matchin the fender well roll.

 

[ninjatek 10+ year member]

if you are enclosing the amps in plexiglass I would suggest some fans and a path for the air to leave.. they might get HOT. im running into that problem with my amps.. have them in an amp rack, with plexiglass, and they are getting too hot without adequate ventilation

 

[Nascarfan 10+ year member]

Im back, yea about the fan design, I already have a pass thru fan design that I will be installing, exactly what you are describing, as for the contures of my fenderwells, well that was a bit difficult, I just began with several pieces of cardboard, and kept shapingit until if formed the angle, then I took that cardboard and drew it onto the wood, then I used a jigsaw to cut it out, then did some sanding, but I left myself enough roon so that when my carpet was glued on ,that i would have just enough space for it to fit, I still have the original templates that i made if someone needs them.

 

[Nascarfan 10+ year member]

Ill take A much higher resoloution picture and post it tomorrow after I get home from work

 

[RipDaJacka]

imma try that! thanks, someone also told me to bend a coathanger to replicate the contours.. imma give em both a try