Incriminator Audio needs your help!

Yeah, a ****in badass 5/6ch amp. With selectable bandpass on one set of channels...digital xovers on it? maybe?
Like...

Channels:

1&2: 50rms @4ohm (Highpassable 24dB/oct )

3&4: 100rms @4ohm... 200ish @2ohms... (bandpassable 24dB/oct)

5: Like 1200-1800rms @1ohm... subsunic... lowpass

w00t w00t w00t!!!

nG
good idea //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif ... but the amp has to run on the same ohm

i wish i could i have a 100x4 / 1200x1

you could have it 6 channels and have the last 2 manditory bridged at like 8 ohms with 1200 rms ... so everything can run on 4 ohms ... somethings wrong with that right //content.invisioncic.com/y282845/emoticons/crying.gif.ec0ebefe590df0251476573bc49e46d8.gif like it drains to much power or something ?

 
or you can put 2 amps designed in 1 so you can put the mono at 1 ohm and have 3 sets of rca's (front / rear / sub) and have a switch that makes them all run off the same rca

and inside the amp it would have a distribution block so the power wire splits into the 2 different amps

 
good idea //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif ... but the amp has to run on the same ohm
i wish i could i have a 100x4 / 1200x1

you could have it 6 channels and have the last 2 manditory bridged at like 8 ohms with 1200 rms ... so everything can run on 4 ohms ... somethings wrong with that right //content.invisioncic.com/y282845/emoticons/crying.gif.ec0ebefe590df0251476573bc49e46d8.gif like it drains to much power or something ?
lol that would be perfect for my current setup //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 
good idea //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif ... but the amp has to run on the same ohm
i wish i could i have a 100x4 / 1200x1

you could have it 6 channels and have the last 2 manditory bridged at like 8 ohms with 1200 rms ... so everything can run on 4 ohms ... somethings wrong with that right //content.invisioncic.com/y282845/emoticons/crying.gif.ec0ebefe590df0251476573bc49e46d8.gif like it drains to much power or something ?
No.

You'd essentially have TWO small 2channel amps and a Mono amp in one case...

But more than likely, Nick would end up with a 4channel amp and a mono amp in one case...

nG

 
No. 

You'd essentially have TWO small 2channel amps and a Mono amp in one case...

 

But more than likely, Nick would end up with a 4channel amp and a mono amp in one case...

 

nG
 

That would be nice...that way the sub channel would have it's own power supply.

 
150x4@4 - channel 1\2 and 3\4 have independent gain. both have bandpassable crossovers @ 24db\oct

800x2@4 - again, independent gain AND powersupplies\fuses, for the people who use them, a potentiometer knob that attenuates the input voltage and does not modify the gain. again, 24db\oct AND subsonic. [mono input]

exterior powersupply would be cool, but i would vote for a TALLER\WIDER amp, rather than a longer amp. double stack the insides.

onboard 1\3oct EQ would be sick as hell too. not sure how you would achieve this though.

and the winner of this raffle will get 2 free pairs of comps and subs //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

i think that would be sick. $10\tix. id be in for like 5.

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

About this thread

Incriminator

10+ year member
Sub Designer
Thread starter
Incriminator
Joined
Location
Alabama
Start date
Participants
Who Replied
Replies
131
Views
5,508
Last reply date
Last reply from
KngOfThePkngLot
IMG_20260516_193114554_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0
IMG_20260516_192955471_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0

New threads

Top