Ranger98
Ridin Dirty
I'm wanting to build a box for my truck, it's a 98 Ford Ranger extended cab.
I have 2 10" JVC CS-DX25 woofers rated at 1300w max.
Woofer specs:
10" Subwoofer
Max. Music Power 1400 Watts
Aluminum Die-Cast Frame
Butyl Rubber Edge
Aluminum Diaphragm + Paper Cone
Aircooling System
Strontium Magnet
Nickel-Plated Screw Terminals
Dual-Input Voice Coil
I mainly listen to rock and country music, but sometimes I like to throw something that's has some heavy bass to show it off.
I don't know how big the box needs to be to be effective. or what kinda box to build for it sound good.
I'm pushing them with 2 Audiobahn A8000 amps, if that helps.
Amp specs:
1600W Max, Intake Series Monoblock Amplifier
RMS Power Output:
400 watts x 1 chan. @ 4 ohms
800 watts x 1 chan. @ 2 ohms
Max Power Output: 1600 watts @ 2 ohms
Class A/B MOSFET Circuitry
PWM MOSFET Power Supply
Semi-double Sided Glass Epoxy Circuit Board
4-way Protection Circuitry: Thermal, Short Circuit, Overload and DC Offset
Air Induction Cooling Fan
Cobalt Blue Illumination
Speaker level (high-level) inputs
Preamp outputs
Nickel-Plated Block Terminals
Optional Remote Bass Control (Audiobahn ABR100T sold separately)
Optional Remote-mount Digital Volt-meter display (Audiobahn ADM100T sold separately)
Variable Bass Boost Control: 0-18dB @ 45Hz
Variable Low-Pass Crossover: 50-120Hz
Signal-to-Noise Ratio: 100dB
Frequency Response: 10Hz-40kHz
Variable Subsonic Filter: 20-50Hz
THD: 0.02%
Phase Control: 0 or 180°
Input Sensitivity: 200mV-8V
Also, haow would you wire them up to get them down to 2 ohms?
Thanks for all the help.
I have 2 10" JVC CS-DX25 woofers rated at 1300w max.
Woofer specs:
10" Subwoofer
Max. Music Power 1400 Watts
Aluminum Die-Cast Frame
Butyl Rubber Edge
Aluminum Diaphragm + Paper Cone
Aircooling System
Strontium Magnet
Nickel-Plated Screw Terminals
Dual-Input Voice Coil
I mainly listen to rock and country music, but sometimes I like to throw something that's has some heavy bass to show it off.
I don't know how big the box needs to be to be effective. or what kinda box to build for it sound good.
I'm pushing them with 2 Audiobahn A8000 amps, if that helps.
Amp specs:
1600W Max, Intake Series Monoblock Amplifier
RMS Power Output:
400 watts x 1 chan. @ 4 ohms
800 watts x 1 chan. @ 2 ohms
Max Power Output: 1600 watts @ 2 ohms
Class A/B MOSFET Circuitry
PWM MOSFET Power Supply
Semi-double Sided Glass Epoxy Circuit Board
4-way Protection Circuitry: Thermal, Short Circuit, Overload and DC Offset
Air Induction Cooling Fan
Cobalt Blue Illumination
Speaker level (high-level) inputs
Preamp outputs
Nickel-Plated Block Terminals
Optional Remote Bass Control (Audiobahn ABR100T sold separately)
Optional Remote-mount Digital Volt-meter display (Audiobahn ADM100T sold separately)
Variable Bass Boost Control: 0-18dB @ 45Hz
Variable Low-Pass Crossover: 50-120Hz
Signal-to-Noise Ratio: 100dB
Frequency Response: 10Hz-40kHz
Variable Subsonic Filter: 20-50Hz
THD: 0.02%
Phase Control: 0 or 180°
Input Sensitivity: 200mV-8V
Also, haow would you wire them up to get them down to 2 ohms?
Thanks for all the help.