Gumbysmoke's '01 Alero

[walled01alero 10+ year member]

looks good so far. make sure to seal off the box from the cabin or you will get cancelation.

yeah i see alot of e-foam in my future.

 

[basscort2009 5,000+ posts]

yep i ended up using like 19 cans on my whole car for sealing, sound deadning the empy back panels and all that

 

[walled01alero 10+ year member]

**** thats quite a bit, that stuff gets nasty if you get it on your hands/clothes.

btw do you have any loading issues with the sub firing into to cabin? i hope my sub doesn't bottom out with the doors open or something since i have a decent amount of port area and almost 5ft^3 box..

 

[LDW3RD 10+ year member]

Looking good.

 

[basscort2009 5,000+ posts]

5 cubes for a 15 plus alot of port area? yea it may unload alot. i have 5 cubes for my 18. but then again i have 10k going to it. if u dont have a ton of power u may be ok

 

[walled01alero 10+ year member]

it's gunna be like 2.4k rated and actually 4.7 cubes @ 32 - 34 for daily and 40 somthing for spl.

that seems like a small box for an 18, though i dont know the parameters on that lvl 6, but it's probly good to go a little smaller with all that power.

 

[jdmferio13 10+ year member]

what kind of deadener you using

 

[walled01alero 10+ year member]

haha it's peel n seal, look at the picture at the end of page 1; that's about how my whole car is covered. It's seriously way cheaper than dynamat or second skin, and literally works exactly the same in my opinion. I got a 3ft x 35.5ft roll for $90 at home depot, covered the whole car (3 to 4 layers on the roof) and still have a shit ton left over. i braced the center of my roof against the stock bar thing that goes across with e-foam and it is really solid (i can pound my fist on the roof and hear just a quiet thud).

it doesn't smell at all when it gets hot as well

 

[walled01alero 10+ year member]

These next two just show some e-foam in cracks/passthroughs between the cabin/trunk

I've also got alot in the side wall wells pushing against the side panels. No more flex ftw...

This is how i chose to color the terminals, i also taped them off in order to spray the washers black

Finished paining test port #1 / cut a few inches off.. (34hz)

 

[walled01alero 10+ year member]

this is how the box for ojthebassman's xxx 15 is looking as of last night

Edit:

p.s. it's going in a geo metro...

 

[OJtheBassman 10+ year member]

//content.invisioncic.com/y282845/emoticons/blush.gif.99bc659ee2012b7d826165e26fb5eebe.gif so pretty

 

[dtbrown 10+ year member]

Looks really good. Just got to flare other end of port to really get full effect of an aero port. Just from flaring the other end you'll gain an easy DB if not more. If it helps this is my friends alero build. 150+ db on 44hz with 2500w and two 12's.

 

[treylittlefield 10+ year member]

where did u get the terminals at?

 

[walled01alero 10+ year member]

Looks really good. Just got to flare other end of port to really get full effect of an aero port. Just from flaring the other end you'll gain an easy DB if not more. If it helps this is my friends alero build. 150+ db on 44hz with 2500w and two 12's.

yea i dont have the capability of making the full flare, but i do know the benefits. i just did it like this because i have to be able to fold my seats up and i didn't want to buy one from amartin.

 

[walled01alero 10+ year member]

black silicon on the ports = solid as shit. black latex paint over both boxes = good idea.

before smoothing..

kinetik voltage with car off..

last night after finishing the xxx build we tested the box side loaded in a huge van and it was slamming. it's going to be bananas in a small geo.

p.s. the btl is arriving tomorrow around 5 while im at f*cking work..