amp for 2 12" rl-p?

chris96camaro
10+ year member

Foreign and Domestic
What amp do most people use to power two 12"soundsplinter rl-p's?

Ok i see that hifonics *****, does anybody know of a moderately priced amp that will put 600-700watts x2@2ohms?

Could i run the kenwood kac-9152(900rms@2ohms) to one of them for a while, then if i decide to get another strap another kenwood to it and run it like that?

 
check the sig, and if you want to buy an eD within this week a group buy is going on that saves you $50 making the total $300 (incl. s&h).

 
nine.1

i'd sell you mine, but this **** group buy is a better deal than I can give you //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

 
Is the jbl 1201.1 a good choice? 1114 watts RMS x 1 @ 2 ohms 14.4V

Does jbl make good amps?

How about the MTX 1501D, 1000 rmsx1@2ohms, are MTX amps usually good about coming cloe to their rated power?

 
Is the jbl 1201.1 a good choice? 1114 watts RMS x 1 @ 2 ohms 14.4V
Does jbl make good amps?

How about the MTX 1501D, 1000 rmsx1@2ohms, are MTX amps usually good about coming cloe to their rated power?

ur getting 1200 at 1 ohm at 12.5 Volts from eD..........right now watt per dollar with build quality in the mix eD has the best amp in t hat range, matter of fact, ordered mine yesterday

 
ur getting 1200 at 1 ohm at 12.5 Volts from eD..........right now watt per dollar with build quality in the mix eD has the best amp in t hat range, matter of fact, ordered mine yesterday
How much is that @2ohms, because the subs can only be wired down to 2??

 
i dont think hifonics *****. however there are better amps. i dont have my rlpd4's yet but i do have a bx1500 and if it isnt good enough ill switch. but 200 bucks they are good for the buck i think. i have not tuned my 6400 yet but it sounds good as is.

 
u got dual 2?????????????? wtf? anyways.....900-1000 at two ohm
The subs are 12"rl-p, dual 4ohm , so they can only be wired down to 2 ohms...

And do you guys think one will be enough, i mean i dont know how loud these things get?

 
The subs are 12"rl-p, dual 4ohm , so they can only be wired down to 2 ohms...
And do you guys think one will be enough, i mean i dont know how loud these things get?


wrong.....u wire EACH to 2ohms.......run them together at 1 ohm. ur final load will be one ohm.

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

Similar threads

Subs play to the beat with gain low but if I turn it up my subs play loud unwanted never ending bass that is constant and wont stop until I turn...
0
51
Getting a good voltage reading does not mean good power transfer. You could read 13.8v out of a 24 AWG wire. Recheck your amplifier's ground and...
2
250
No need to bypass the amp. Most use an LOC that takes the full amped signal and turns it into a flat RCA level signal. Here is the newest I have...
2
459

About this thread

chris96camaro

10+ year member
Foreign and Domestic
Thread starter
chris96camaro
Joined
Location
Charlotte, NC
Start date
Participants
Who Replied
Replies
14
Views
612
Last reply date
Last reply from
denim
received_1404248310277849.jpeg

Blackout67

    Jun 10, 2024
  • 0
  • 0
445981256_3731324230470906_9081536917273579948_n.jpg

Decebal

    Jun 10, 2024
  • 0
  • 0

New threads

Top