amp for 2 12" rl-p?

chris96camaro
10+ year member

Foreign and Domestic
What amp do most people use to power two 12"soundsplinter rl-p's?

Ok i see that hifonics *****, does anybody know of a moderately priced amp that will put 600-700watts x2@2ohms?

Could i run the kenwood kac-9152(900rms@2ohms) to one of them for a while, then if i decide to get another strap another kenwood to it and run it like that?

 
check the sig, and if you want to buy an eD within this week a group buy is going on that saves you $50 making the total $300 (incl. s&h).

 
nine.1

i'd sell you mine, but this **** group buy is a better deal than I can give you //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

 
Is the jbl 1201.1 a good choice? 1114 watts RMS x 1 @ 2 ohms 14.4V

Does jbl make good amps?

How about the MTX 1501D, 1000 rmsx1@2ohms, are MTX amps usually good about coming cloe to their rated power?

 
Is the jbl 1201.1 a good choice? 1114 watts RMS x 1 @ 2 ohms 14.4V
Does jbl make good amps?

How about the MTX 1501D, 1000 rmsx1@2ohms, are MTX amps usually good about coming cloe to their rated power?

ur getting 1200 at 1 ohm at 12.5 Volts from eD..........right now watt per dollar with build quality in the mix eD has the best amp in t hat range, matter of fact, ordered mine yesterday

 
ur getting 1200 at 1 ohm at 12.5 Volts from eD..........right now watt per dollar with build quality in the mix eD has the best amp in t hat range, matter of fact, ordered mine yesterday
How much is that @2ohms, because the subs can only be wired down to 2??

 
i dont think hifonics *****. however there are better amps. i dont have my rlpd4's yet but i do have a bx1500 and if it isnt good enough ill switch. but 200 bucks they are good for the buck i think. i have not tuned my 6400 yet but it sounds good as is.

 
u got dual 2?????????????? wtf? anyways.....900-1000 at two ohm
The subs are 12"rl-p, dual 4ohm , so they can only be wired down to 2 ohms...

And do you guys think one will be enough, i mean i dont know how loud these things get?

 
The subs are 12"rl-p, dual 4ohm , so they can only be wired down to 2 ohms...
And do you guys think one will be enough, i mean i dont know how loud these things get?


wrong.....u wire EACH to 2ohms.......run them together at 1 ohm. ur final load will be one ohm.

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

Similar threads

No need to bypass the amp. Most use an LOC that takes the full amped signal and turns it into a flat RCA level signal. Here is the newest I have...
2
152
It would also be easy to add an equalizer to have individual rca inputs for all of the channels. A decent one can be had for less than $40...
6
385
  • Locked
NVX MVPA1 Best tiny amp Installed a bunch, but have one pushing a sealed 12 @ 2ohm in my daily beater Can bump it all day long and barely gets...
4
690
Amp
This tested well on youtube - not familiar with the brand but it is a pretty standard china build house amplifier...
5
499

About this thread

chris96camaro

10+ year member
Foreign and Domestic
Thread starter
chris96camaro
Joined
Location
Charlotte, NC
Start date
Participants
Who Replied
Replies
14
Views
610
Last reply date
Last reply from
denim
Buick Amp Connector.JPG

maylar

    Jun 2, 2024
  • 0
  • 0
1717274743729.png

Doxquzme

    Jun 1, 2024
  • 0
  • 0

New threads

Top