Very 1st glassing project~ *PIXPIXPIX*

flakko
5,000+ posts

Veteran (my butt)
After a month of drivin around with these speakers sitting on the floor, i finally got around to glassing my Rainbows in. This is what ive done tonite so far:

Heres a pic of what it used to look like:

glassin017zo.jpg


A little before shot:

glassin028qu.jpg


All the tape and stuff:

glassin030wv.jpg


And done for the night leting it dry (do i need another layer?):

glassin041bt.jpg


Now my only problem was the taping... i didnt put foil and stuff underthe tape. I hope everythings okay underneath the tape //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

but overall looks okay to me.

will keep u updated! //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 
um.

why are you putting them on the SIDE of the car like that? they should be put in the corner under the deadpedal where the plastic foot thing is... or at least as close up to that part as possible...

i guess its looking good so far tho.

 
um.

why are you putting them on the SIDE of the car like that? they should be put in the corner under the deadpedal where the plastic foot thing is... or at least as close up to that part as possible...

i guess its looking good so far tho.
Yep, the main point of kicks is to make the pathlengths of the two speakers somewhat close for better imaging, also the flexibility for aiming, the position you have them in now looks like it would be worse than stock, same place just lower.

 
um.

why are you putting them on the SIDE of the car like that? they should be put in the corner under the deadpedal where the plastic foot thing is... or at least as close up to that part as possible...

i guess its looking good so far tho.
I knew someonewas gonna ask that lol

but the reason for that is, i dont have room to put it anywhere else. my e-brake takes up the majority of the corner. and after listening to it the way i had it, the music sounded fine to my ears. It may not have PERFECT imaging, but its the best i could do with the limited space.

 
shyt son, if it were me, id get somone with some welding skills, hack that deadpedal off, have them weld a bar so you can move it back\over (like near the regular brake like where the clutch would be) and then your kick is totally free.

and welding it on would take like 20 minutes to do

 
shyt son, if it were me, id get somone with some welding skills, hack that deadpedal off, have them weld a bar so you can move it back\over (like near the regular brake like where the clutch would be) and then your kick is totally free.
and welding it on would take like 20 minutes to do
lol thats cool!! its fine the way it is tho //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

i listened to the speakers against the dead pedal, and it didnt sound all that hot for some reason. I guess its the car i dunno

 
lol thats cool!! its fine the way it is tho //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

i listened to the speakers against the dead pedal, and it didnt sound all that hot for some reason. I guess its the car i dunno
hmm hard to imagine them imaging better where they are but if your ears say so //content.invisioncic.com/y282845/emoticons/cool.gif.3bcaf8f141236c00f8044d07150e34f7.gif

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

About this thread

flakko

5,000+ posts
Veteran (my butt)
Thread starter
flakko
Joined
Location
So Cal
Start date
Participants
Who Replied
Replies
105
Views
3,057
Last reply date
Last reply from
flakko
IMG_20260516_193114554_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0
IMG_20260516_192955471_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0

New threads

Top