need help

Dmatt

Junior Member
ok so i am buying 3 kicker cvr's 4ohm. i have a monoblock 600 rms alpine amp as of now. i have already made the box for the subs, however i know my amp isnt strong enough to run all 3 since they are 400 rms each sub, is it possible to run 2 of the subs off of the 1 amp i have now and then get a smaller one and run the other sub, even with them all in the same box? or will this make them sound terrible

 
do you even know what ohm load your gonna present your amp with with the three subs? or do you just plan on wiring them all in parallel adn dropping that amp below its stability?

 
just run all 3 off the same amp (it'll underpower the subs but still be decent) then when u get the money buy a bigger amp.

It will still hit hard? and i wont blow any of the subs or the amp?

do you even know what ohm load your gonna present your amp with with the three subs? or do you just plan on wiring them all in parallel adn dropping that amp below its stability?

im not sure truthfully, i was going to have it installed by a professional so i dont screw it up, i was just told if i run 3 on my amp that it would blow my amp, so i thought maybe i could run 2 on my amp now and then one of them on another amp, but then i was told it wouldnt sound right..

 
just run all 3 off the same amp (it'll underpower the subs but still be decent) then when u get the money buy a bigger amp. It will still hit hard? and i wont blow any of the subs or the amp?

do you even know what ohm load your gonna present your amp with with the three subs? or do you just plan on wiring them all in parallel adn dropping that amp below its stability?

im not sure truthfully, i was going to have it installed by a professional so i dont screw it up, i was just told if i run 3 on my amp that it would blow my amp, so i thought maybe i could run 2 on my amp now and then one of them on another amp, but then i was told it wouldnt sound right..
//content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif do you know what ohm load your amp is stable down to? and are the cvrs dual 4 ohm voice coil?

 
yea if you bring the amp below its ohms it will make the amo unstable thats bad for the amp. did you already get the d4s or are you going to get them. iam looking for the website with wire diragrams brain fart cant think of it

 
what part of florida are you in...i'll charge you less if you are there and actually try and learn...if not just hooking everything up (if amp isnt installed) is $45.
hit him up on this. or your gonna get fuccked over in the end. who knows what the shop will to do to make a buck

 
st. cloud isnt far...hell if you pay for my gas (isnt much i drive a crx) and lunch i could help you and teach you a few things.

number is 407 459 2572(before the 26th) and then 407 692 8116(after)...hit me up...

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

About this thread

Dmatt

Junior Member
Thread starter
Dmatt
Joined
Location
Florida
Start date
Participants
Who Replied
Replies
21
Views
1,077
Last reply date
Last reply from
cj407
IMG_20260516_193114554_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0
IMG_20260516_192955471_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0

New threads

Top