Need Help finding Amp Kit

[ddog003]

Hey, I just got 2 Infinity Kappa Perfect 10.1d subs and an Infinity Reference 611a amp to power them. I was just wondering what would be the ideal amp kit for this and if anyone knows where to get one for a good price. I am also a bit condused on how I should wire my subs to my amp. Is this amp good for these subs? Here are the specs below. Thx.

Each Sub

Size: 10 inch

Rec. Sealed Box Dims: .6 - .6 cu.ft.

Rec. Ported Box Dims: 1 - 1 cu.ft

Free Air Usage: not recommended

Sensitivity: 94 dB

Frequency Response: 18-150 Hz

Recommended RMS Power: 350W

Peak Power Handling: 1400W

Impedance: dual 4 ohms subwoofer wiring options

Amp

Amplifier Type: Mono

RMS Power: 456W x 1 @ 4 ohms

THD at 4-Ohm RMS Power:

Bridged RMS Power: 657W x 1 @ 2 ohms

Speaker Level Inputs: no

Preamp Outputs : yes

Built-In Crossovers: LP

Bass Boost: 0 - 12 dB

Frequency Response: 17-302 Hz

Signal to Noise Ratio: 70 dB

Fuse Rating: 2 x 30 amps

Click to read more...

 

[Raffi 10+ year member]

Hey, I just got 2 Infinity Kappa Perfect 10.1d subs and an Infinity Reference 611a amp to power them. I was just wondering what would be the ideal amp kit for this and if anyone knows where to get one for a good price. I am also a bit condused on how I should wire my subs to my amp. Is this amp good for these subs? Here are the specs below. Thx.
Each Sub

Size: 10 inch

Rec. Sealed Box Dims: .6 - .6 cu.ft.

Rec. Ported Box Dims: 1 - 1 cu.ft

Free Air Usage: not recommended

Sensitivity: 94 dB

Frequency Response: 18-150 Hz

Recommended RMS Power: 350W

Peak Power Handling: 1400W

Impedance: dual 4 ohms subwoofer wiring options

Amp

Amplifier Type: Mono

RMS Power: 456W x 1 @ 4 ohms

THD at 4-Ohm RMS Power:

Bridged RMS Power: 657W x 1 @ 2 ohms

Speaker Level Inputs: no

Preamp Outputs : yes

Built-In Crossovers: LP

Bass Boost: 0 - 12 dB

Frequency Response: 17-302 Hz

Signal to Noise Ratio: 70 dB

Fuse Rating: 2 x 30 amps

I would say 4 guage amp kit with a ANL fuse holder.. And the subs wired parallel. Positive-Positive........Negative-Negative....down to 2 ohm

 

[Raffi 10+ year member]

Ok I just saw that you have 2 4ohm DVC...so forget the parallel wiring...

 

[johnecon2001 5,000+ posts]

There are only two practical ways to wire those subs. And only one that will work with your amp without blowing it up.

http://www.rockfordfosgate.com/rftech/wiringwizard.asp?WoofQty=2+woofers&WoofImp=Dual+Voice+Coil+-+4+ohms+x+2

Use the one that puts the subs to 4ohms. Or buy dual 2 ohm subs. Or buy a new amp.

 

[.::DuD3::. 10+ year member]

Hey, I just got 2 Infinity Kappa Perfect 10.1d subs and an Infinity Reference 611a amp to power them. I was just wondering what would be the ideal amp kit for this and if anyone knows where to get one for a good price. I am also a bit condused on how I should wire my subs to my amp. Is this amp good for these subs? Here are the specs below. Thx.
Each Sub

Size: 10 inch

Rec. Sealed Box Dims: .6 - .6 cu.ft.

Rec. Ported Box Dims: 1 - 1 cu.ft

Free Air Usage: not recommended

Sensitivity: 94 dB

Frequency Response: 18-150 Hz

Recommended RMS Power: 350W

Peak Power Handling: 1400W

Impedance: dual 4 ohms subwoofer wiring options

Amp

Amplifier Type: Mono

RMS Power: 456W x 1 @ 4 ohms

THD at 4-Ohm RMS Power:

Bridged RMS Power: 657W x 1 @ 2 ohms

Speaker Level Inputs: no

Preamp Outputs : yes

Built-In Crossovers: LP

Bass Boost: 0 - 12 dB

Frequency Response: 17-302 Hz

Signal to Noise Ratio: 70 dB

Fuse Rating: 2 x 30 amps

There are only two practical ways to wire those subs. And only one that will work with your amp without blowing it up.http://www.rockfordfosgate.com/rftech/wiringwizard.asp?WoofQty=2+woofers&WoofImp=Dual+Voice+Coil+-+4+ohms+x+2

Use the one that puts the subs to 4ohms. Or buy dual 2 ohm subs. Or buy a new amp.

thats why it pays to research this stuff ahead of time //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif.