Need 1/0 wire for Big 3

[TheUnderFighter 10+ year member]

Measured it to be about 8ft total in length for my car, so, I need an 8ft run of some 1/0, I'd like Kolossus Kable or something similar in quality and flexibility, and most importantly, a good price I will also need ring terms included, 6 of course. I am on a budget!

Click to read more...

 

[hrtbrk1 5,000+ posts]

got 9 ft of kicker hyperflex and 6 terms. 45 shipped

 

[TheUnderFighter 10+ year member]

bump.

 

[hrtbrk1 5,000+ posts]

//content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

 

[TheUnderFighter 10+ year member]

Sorry man. haha, 4 bucks a foot for used is just outta my price range. Worse comes to worst, I'll just buy it new.

 

[hrtbrk1 5,000+ posts]

well that price was with 6 ring terms shipped.

 

---------- Post added at 11:14 PM ---------- Previous post was at 11:14 PM ----------

 

also...copper has gone up and this is ofc wire. even throw in a fuse if you need it and a starter run

 

[TheUnderFighter 10+ year member]

I know. that's why I said 4 bucks a foot, which is 36 bucks. plus a few bucks for terms, and then a few more for shipping. 45 bucks. Tis just outta my range. Especially when I got a 2 gauge run at 15 bucks.

 

[vitveet 10+ year member]

Email me at vitveet@hotmail.com I have 2 seperate 26 ft rolls of 2/0 welding wire and is fairly flexible! Will cut to whatever length you want/need. It's black in color.

V.

 

[select127 10+ year member]

checkout my thread.

http://www.caraudio.com/forums/electrical-wiring-classifieds/513011-f-s-used-wire-1-0-small-pieces-4ga.html

 

[hrtbrk1 5,000+ posts]

$40?

 

[TheUnderFighter 10+ year member]

select, I wish your pieces were big enough man, no long enough runs>.

and heartbreak, it's just not in the budget right now man, I'm sorry. If you wanted to do 35 shipped, for the wire and terms next week when I get paid again, I could do that. But I also understand that's not a great deal for you either.

 

[hrtbrk1 5,000+ posts]

i understand man...what are the exact length of pieces do you need? i got some scrap ones too //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[TheUnderFighter 10+ year member]

Well bat to ground is SUPER short, like, 6 inches or less... it's bat to alt that is the long one, I think around 5 feet. And then engine block to gnd is a couple feet at most.

 

[hrtbrk1 5,000+ posts]

ahh i see...well if you plan on fusing the alt to batt you can use two short runs as well //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[TheUnderFighter 10+ year member]

Now you want me to buy a fuse?! haha, yet another increase in cost!

 

[hrtbrk1 5,000+ posts]

lol no im not..eeven if i was i dont have a fuse holder to sell you so it wont do me any good