Look look! I can cut out a circle!!!

[bjfish11 5,000+ posts]

impressive, although i still laugh my *** off everytime i see that pic. Thanks again for all the good times. LOL

 

[flakko 5,000+ posts]

lol why do you have your insurance card on your box?

erm... well i didnt have any paper to write on at hand so i used that insurance paper for cutting dimensions.

 

[imaspaceguy90 10+ year member]

no leakes! put it up to a light!
i mean compared to this:

prettty dang good no?

Thas a ****ed up circle

 

[Raisedin305 5,000+ posts]

no leakes! put it up to a light!
i mean compared to this:

prettty dang good no?

//content.invisioncic.com/y282845/emoticons/rotflol.gif.b453361716769b8110ddefc85ff03cd2.gif Holy shit! Didn't think it was that bad.

 

[phantom240 5,000+ posts]

that box makes me feel better about my OWN life.... wow

 

[Eldorado 5,000+ posts]

The crazy thing is...

The sub actually fit in that and covered it all up

 

[flakko 5,000+ posts]

lik i said.... ART

 

[project f-150 10+ year member]

with that cut it looks like the person wasnt sure if he had a round or square sub

 

[ramos 5,000+ posts]

Getting there my brother. Definately looks better than your previous. Just a question, Are you using a straight edge with the circular saw ? //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[theCybe 5,000+ posts]

it is it is! Eldorado, JAZN and i (actually just eldorado) ran the box over with his burban hehe.

Thank god //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[nVRuckus 5,000+ posts]

yup! every box i make i get better and better. only if i had a table saw... //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

I have one and still end up using a regular circular saw to cut the full MDF and just use the table saw for smaller cuts. that big MDF isnt very movable on a table saw //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

what you need is a router cause that hole is shaky

 

[flakko 5,000+ posts]

Getting there my brother. Definately looks better than your previous. Just a question, Are you using a straight edge with the circular saw ? //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

nope... i think thats where i can improve

I have one and still end up using a regular circular saw to cut the full MDF and just use the table saw for smaller cuts. that big MDF isnt very movable on a table saw

yea i need the table saw to finetune my cuts you know... cut a little bit bigger, and cut off the excess with a table saw

 

[Eldorado 5,000+ posts]

DIdnt i tell you to use a scrap piece of MDF and 2 clamps as a fence ?

 

[phantom240 5,000+ posts]

lol

 

[~Magick_Man~ 10+ year member]

well like you said, it is improvement.

so go ahead and build about 5 more boxes and you might end up with a round hole by the end //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

also JASPER CIRCLE JIG FTW. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

~Magick_Man~