Sold High End Equipment 4 Sale - Dynaudio, Arc, IDMax

[AZDave 10+ year member]

Pictures of my install can be found here: http://www.cardomain.com/memberpage/786464

Image Dynamics IDMax 12V3D2

$225 plus shipping - SOLD

- Bought new from Sounddomain in Febuary

- Shipped in original boxes

This is a lightly used and adult owned subwoofer. I had two of these, each in a 1 cuft sealed enclosure, powered by one 1000W arc audio amplifier (Available in another auction). That means they each only saw 500W. This is one of the reasons I bought them, because they are very efficient and don’t need much power.

Arc Audio 1500DR

$250 plus shipping Sold

- 900x1 @ 4ohm RMS

- 1000x1 @ 2ohm RMS

Used and adult owned 1500-DR in blue. I used it to power by a pair of IDMax 12’s (Available in my other auction). The mounting feet are bent, and there is a large scratch on the top of the amp. It recently got back from Arc Audio, where a new Tripath chip was installed. I have a copy of Arc Audio’s test report for the amp, and internally it’s great. Serial number is intact.

Frequency Response: 20Hz - 20kHz

S / N Ratio (A wtg.): >98dB

Separation @ 1kHz: >65dB

Transient Distortion (100W): Input Sensitivity: 250mV - 2.5V

Bass Boost: 0-15dB @ 45Hz

Crossover: 12db stereo, 24db mono 50hz-550hz

Input Impedance: 33Kohms

Max. Current Requirement: 120A @ 1,000 watts

Idle Current: 1.75A

Dimensions: 15.25" x 8" x 2.35"

Dynaudio System 340 3-Way Components

See these at http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=5780663776

This is a set of adult owned Dynaudio System 340’s that were in my car for 4 months, and the speakers are in mint condition. They were powered by my Arc Audio CXLR 4150 (Available in my other auction), and if you’re looking at this auction you know they sound awesome. I still have the original box and manual.

Three-way set includes:

MW 160 7“ MSP one-piece cone woofer with 3“ aluminum voice coil

MD 140 3“ soft dome midrange with 3“ aluminum voice coil, sealed and acoustically damped rear chamber

MD 100 1.1“ neodymium dual-magnet soft dome tweeter

Plus all hardware, grilles, crossover and accessories. Audiophile quality crossover (X 360) is adjustable for three different tweeter operational modes. Phase correct, shallow slope crossover. Die-cast basket. Frequency response: 55 Hz - 25 kHz; 91 dB sens. 200 watts continuous.

Click to read more...

 

[req 5,000+ posts]

dude. props to that install - clean as a whistle, and somone finally using the 'use your stock kick panels' to make your aftermarket kicks.

mad props. those 3way dynaudio's are sweeet. thats prolly the kind of component set i would run if i went that way. and that amp is awesome //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

free bump - awesome stuff.

 

[Matt000 10+ year member]

pm sent!

 

[TooLowTooGo 10+ year member]

deffinetly a nice setup.. u do some good work.

free bump also

 

[AZDave 10+ year member]

Thanks for the compliments guys! To tell everyone the truth, I have more fun doing installs than actually listening to them //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[94CamryBumpin 10+ year member]

i have a 1994 Camry...how did u make the box in the trunk look like it did from the trunk...looked like a factory wall off job...very nice install...

 

[AZDave 10+ year member]

Thanks! I used cardboard and an exacto knife to the make traces of the side walls. Once I had traces for both sides, I used a tape measure to the measure the distances between the the top and bottom of each side. Then I traced the cardboard forms onto a piece of 1/2" mdf, seperated by the distance between them that I measured. That 1/2" is just a trim piece then that I glued and screwed onto the back of the real sub box (3/4" MDF).

 

[AZDave 10+ year member]

I just have the Dynaudios left!

 

[AZDave 10+ year member]

Bump!