dual amps in general ****. get something better. hifonics is better than dual.
*deleted*
read post below...
read post below...
800W x 1 peak output @ 2 ohms
500W x 1 peak output @ 4 ohms
250W x 1 continuous output @ 4 ohms
360W x 1 continuous output @ 2 ohms
the most this amp will do (rated) is 360w rms x 1 @ 2 ohms. when u had them wired at 4 ohms, they were putting out 250w rms.
dont pay attention to the peak ratings, thats not what your going to be getting out of the amp. look at continuous or RMS power ratings. if you can wire both @ 2 ohms, that would get you the most power. if not, return, and get a hifnoics //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif
500W x 1 peak output @ 4 ohms
250W x 1 continuous output @ 4 ohms
360W x 1 continuous output @ 2 ohms
the most this amp will do (rated) is 360w rms x 1 @ 2 ohms. when u had them wired at 4 ohms, they were putting out 250w rms.
dont pay attention to the peak ratings, thats not what your going to be getting out of the amp. look at continuous or RMS power ratings. if you can wire both @ 2 ohms, that would get you the most power. if not, return, and get a hifnoics //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif
- Thread Starter
- #7
ok it's a little detailed so here goes. With both connected i have them grounded to the same spot, i have the main power wire and a different wire a foot in length connected into one of the amps power input and then the foot wire going from that first amp to the 2nd ones power input, i have one of the amps connected by the rcas coming from the HU and the other is connected via high inputs, and i have the remote wire from the HU into one of the amps remote input and then i chain off that into the 2nd amps remote input. So could the problem be that i don't have a distro block for the main power? I've already tested out the rca and high input and both give the same sound while just having one amp hooked up.
- Thread Starter
- #8
woah, i know that already, but the 360 is with both subs hooked up to it, there should be 500wrms@4 ohms with both amps though, 250 to each sub... and 500>360 right? Or would the ohm diff matter even with higher wattage?
im getting confused but ya it should be 500 with both amps, but tell me you didnt pay 200 for each of these, meaning you paid 400 for 500(probably less) watts?
return......ftw.
return......ftw.
- Thread Starter
- #10
naw i didn't pay 400, i payed $418 with tax... im trying to think of ways to make the output seem like it's really a 2 ohm load, what if i were to take a stock speaker from my car that has a 4 ohm load and rig it up with one of the subs to make it a 2 ohm load... is it possible to make it to where the sub is taking most of the watts and the stock speaker just does nothing, like if i were to use something like crossover chained somewhere?
iagrdshaka
5,000+ posts
Down with jimmy hats
huh? So you are saying any Hifonics amplifier is better than two IA 20.1s strapped?
lol
does this guy have 2 IA20.1's? no. he has 2 pioneer gm7200s. im sure the new line of hifonics is just as much money and puts out more power for the money (what it seems like he wants)
i dont know where you came outta no where with the IA statement tho...i was comaring to his amps (read his other thread as well, where he blew one up.)
Activity
No one is currently typing a reply...
Similar threads
- Started by Cmberges1
- Amplifiers
- Started by Theo Ray
- Amplifiers
About this thread
- Start date
- Participants
- Who Replied
- Replies
- 26
- Views
- 1,529
- Last reply date
- Last reply from
- Hydrastas
