call me a Ricer but...

[k_schutte 10+ year member]

Ricer butt

 

[BeAlLsTaR13 10+ year member]

you prolly blew a fuse,just tap into anything that runs hot with either the car off or on really, and yeah all positives and negatives ran parallel, i have 3 switches though

exterior lights

interior 1

interior 2

i have them all ran off my cig lighter, then ran parallel for each load, 3 different loads = 3 different connection points

 

[ccab 10+ year member]

if you can send me some more pics of where you ran your loads at and stuff I need as many details as possible. pm'd my email to you.

 

[Ohioguy 10+ year member]

1. google.com

2. then look up, how to install led's.

3. i just gave you more advice than anyone on this site.

 

[TMali 10+ year member]

12v led, red to positive (Power) black to negative (ground)

whats so hard about that??? And any 12v switch will work

 

[ccab 10+ year member]

aight cool. I got it.

 

[iApex 10+ year member]

If you want an easy access point you can get it from the cig lighter by just cutting the wires and splicing into them like I did, or you can run off of the amp in the back of the car. just put your ground to the chassis somewhere. It's not as difficult as most people think.

I got all the stuff for my cars lighting from http://www.oznium.com

They have super good prices and customer support. A local shop blew my cousins lighting and i asked oznium about it and they replaced all of it for free, even though it was not their fault.

 

[bubbagumper6 5,000+ posts]

gay

 

[theMessenjah44 10+ year member]

You weren't very specific on what you're wanting to use. Are you wanting to use LED tubes for your wheel wells/under seat/door pockets, or single LEDs, like up in your vents or whatever. the latter is a little more complicated.

If you're going with the tubes, look at the oznium stuff someone already posted here or I can set you up with some StreetGlow. It's really simple installation, just + and -. Put a switch on one side so you can turn them on and off. Everything's wired in parallel, so you take all your + wires and solder them together, then take all your - wires and solder them together.

If you can't do this, you can't do car audio //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[ccab 10+ year member]

You weren't very specific on what you're wanting to use. Are you wanting to use LED tubes for your wheel wells/under seat/door pockets, or single LEDs, like up in your vents or whatever. the latter is a little more complicated.
If you're going with the tubes, look at the oznium stuff someone already posted here or I can set you up with some StreetGlow. It's really simple installation, just + and -. Put a switch on one side so you can turn them on and off. Everything's wired in parallel, so you take all your + wires and solder them together, then take all your - wires and solder them together.

If you can't do this, you can't do car audio //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

I wanted to put 2 15" tubes under each seat and 2 15" tubes under each side of the dash and do a underbody kit. so whatever suggestions you can give me is appreciated.

 

[ccab 10+ year member]

what all kind of switches and accessories do I need besides the actual tubes..and I was planning on getting them from http://www.ledunderbody.com/neon-led-under-car-undercar-light-kits.aspx?gclid=CIOUn4iX_p0CFQO2sgodrXzspg

because they are cheaper there..I have a 150 dollar budget for an underbody and 4 tubes

 

[iApex 10+ year member]

I wanted to put 2 15" tubes under each seat and 2 15" tubes under each side of the dash and do a underbody kit. so whatever suggestions you can give me is appreciated.

The cathode kit on oznium would work for under the dash and seats. http://www.oznium.com/cathode-kit

It's $8 for 2 tubes and the transformer to power them. Thats what I have in my car, cheap and effective.

I would get streetglow for the underbody.

 

[theMessenjah44 10+ year member]

I have a pair of these in a lighted sign in my garage.

http://www.oznium.com/led-flex-strips

Obviously they have different colors. If you get the million color tubes, you can get this module so you can pause them on any color you want.

http://www.oznium.com/rgb-led-controller

underbody kits

http://www.oznium.com/underbody-kits

 

[ccab 10+ year member]

The cathode kit on oznium would work for under the dash and seats. http://www.oznium.com/cathode-kitIt's $8 for 2 tubes and the transformer to power them. Thats what I have in my car, cheap and effective.

I would get streetglow for the underbody.

where do you see that it says 8 dollars for two? its showing me 10.00 for 1 12"

 

[ccab 10+ year member]

I can get 4 15"s at http://www.ledunderbody.com