Big 3 or Big 4

[Rocky213 10+ year member]

everybody talks about big 3, but with me its more like big 4, i have the engine block to chassis, the neg batt to chassis, the neg alt to battery, and the pos alt to battery...do you guys think thats too many grounds?..

Click to read more...

 

[collin.k 10+ year member]

i'm pretty sure you can never have too many grounds, unless they're poorly made

 

[Rocky213 10+ year member]

whats your definition of poorly made..for the batt neg to chassis i used the ground where the factory wire was just upgraded it to 0 gauge..its right next to the battery only 1 foot of ground wire was used for that..and i did not solder them just crimp..and both the batt neg and engine block are on the same ground..just wondering if its good

 

[AlterEgo99 5,000+ posts]

The bolt mounts on my alternator are the grounds for the alternator, so from a wiring perspective, it's still the Big 3.

 

[hispls 5,000+ posts]

Whether the extra grounds have any practical or measurable effect is up to debate. If you have the wire, it can't hurt and will certainly make your foundation stronger.

 

[AlterEgo99 5,000+ posts]

Whether the extra grounds have any practical or measurable effect is up to debate. If you have the wire, it can't hurt and will certainly make your foundation stronger.

I'll say that it does...I had a very minor alternator whine that I could not get rid of but did have the space for an extra battery up under the hood ('08 Silverado)...so I added the extra battery (have 2 Kinetik HC2000's), wired them in parallel and grounded one to one side of the engine block and the frame, the other to the other side of the engine block and the other side of the frame (frame grounding point was front shock bolt for both)...after I did that, no alternator whine or light dimming...I think it helps.

 

[Rocky213 10+ year member]

i think it helps just had to get a new batt terminal for the neg with so many 0 gauge going in to it, but it sounds better, it even hits different feels like their much less stress on the system..

 

[keep_hope_alive Premium Member]

the alt grounds through the engine block and transmission housing. you want your ground wire as short as possible - whatever path that is. if the ****** is closest - use that, if the block, use that, if the alt bracket, use that.

i NEVER ground on a bolt that is related to suspension or has a torque setting. Make sure to take engine movement into account and always use high-temp split loom or heat shrink to protect your wires. secure them as often as possible, just like factory.

when you are done, it should look like a factory install, everything in loom and well secured.

 

[Rocky213 10+ year member]

i have the engine ground and alternator ground from the alternator itself (mechman 270)..my engine ground was going in the battery neg but i put it to the chassis (same place where the battery neg is going to) is that ok or should i hook it back to the battery?..i also have the alt neg going to the battery..so many wires lol

 

[AlterEgo99 5,000+ posts]

the alt grounds through the engine block and transmission housing. you want your ground wire as short as possible - whatever path that is. if the ****** is closest - use that, if the block, use that, if the alt bracket, use that.
i NEVER ground on a bolt that is related to suspension or has a torque setting. Make sure to take engine movement into account and always use high-temp split loom or heat shrink to protect your wires. secure them as often as possible, just like factory.

when you are done, it should look like a factory install, everything in loom and well secured.

It's one of three...hasn't budged since I did this over a year ago...it's cool. //content.invisioncic.com/y282845/emoticons/fyi.gif.9f1f679348da7204ce960cfc74bca8e0.gif

 

[05fronty 5,000+ posts]

big 5

 

[keep_hope_alive Premium Member]

It's one of three...hasn't budged since I did this over a year ago...it's cool. //content.invisioncic.com/y282845/emoticons/fyi.gif.9f1f679348da7204ce960cfc74bca8e0.gif

just because it can be done doesn't make it a good idea. it compromises the integrity of the connection, especially with some of the soft metal ring terminals being sold.

 

[AlterEgo99 5,000+ posts]

just because it can be done doesn't make it a good idea. it compromises the integrity of the connection, especially with some of the soft metal ring terminals being sold.

I often swin against the tide bro, it's how I roll...don't worry, it's all good. //content.invisioncic.com/y282845/emoticons/thumbsup.gif.3287b36ca96645a13a43aff531f37f02.gif

I will offer a disclaimer tho if it will settle your troubled mind:

Note:

I'm a professional, don't try this at home

 

[keep_hope_alive Premium Member]

lmao. nice.

i'm just cautious about recommending something that people can fawk up and kill themself or someone else. or destroy the car. some of these kids have no business taking suspension bolts off because they are too stupid to understand torque settings. know what i mean?

i will also say "do what i say, not what i DO". :0

 

[keep_hope_alive Premium Member]

the important part is to take your time, do it right, and know what you're doing.