best sub for aq1200d

well you dont want to wire one of the skars at 1 ohm...thats double its rms...it would be perfect if you had two of them...but for one you can wire to 2 ohms or maybe 4...i would buy one dual 4 and wire to 2 ohms and if you want to get another one then wire at 1 ohm

 
so are you looking for lows? if so the skar is an excellent choice or SSA dcons
why dcons and not icons? just wondering

and well im looking for a sub that is great up to 60-80 hz that can also pound down low with clarity!

Also, my verdict for price limit is

 
So I think skar, iconn, dc, or fi. Im surprised no one is pushing for dd woofers![/QUOTE]
Thats because with a budget of 300 or less you could barely get a 2500 series (assuming bought new from dealer). I had a 2510 and its a great sub but for under 300 its not even a top 5 contender. The 3500 and up series is where DD starts to impress me.
 
So I think skar, iconn, dc, or fi. Im surprised no one is pushing for dd woofers![/QUOTE]
Thats because with a budget of 300 or less you could barely get a 2500 series (assuming bought new from dealer). I had a 2510 and its a great sub but for under 300 its not even a top 5 contender. The 3500 and up series is where DD starts to impress me.
thanks, I was curious before hand when i had no limit but I don't compete in spl so I think i should find a product that can satisfy me for that price.. Quick new subject can an re s e x 12" wired to 1 ohm handle a full aq1200? if i set the gains with multimeter, clean signal, good ported box!

^^ if so what gauge wire should i use for my speaker wire? 8 gauge?
 
If you are looking to run the AQ at 1 ohm I would look at the FI Q in a good ported enclosure.

As for you earlier post, no subs do not take up much space. However, the total of port, bracing, 45s, and sub will be a good chunk of space.

 
If you are looking to run the AQ at 1 ohm I would look at the FI Q in a good ported enclosure.
As for you earlier post, no subs do not take up much space. However, the total of port, bracing, 45s, and sub will be a good chunk of space.
I really like Fi audio, their products always look top notch. I would most likely be building my own box, so what type of bracing do you recommend? 45's meaning using a routing table to cut the corner of my port walls to 45 degree angles? I was planning on using one of the free enclosure designs on this site.

I think im limiting my choices to dc, sa, ssa (icon), or fi.. maybe dd if i can get some reasonable prices today..

 
those are the DD 8's ....I'm looking at doing a similar setup with a DD M1B Its about the same power as your amp...The box will be 3cu ft counting port...
I don't know what to choose.. I have to sell my re first. Then I can get an Fi q, which i've always wanted one haha or I can choose from icon,skar, dc, dd.. I'm waiting on thorshammer to write me back on the pricing for dc lvl 4. I have a dealer thats north of me that sells dd audio. Fi also has like 4 options and im not sure which are a necessity (if any). For example cooling, high qts, spider, P chamfer, and I heat ring

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

About this thread

xtullyx

Banned
Thread starter
xtullyx
Joined
Location
Ohio
Start date
Participants
Who Replied
Replies
66
Views
3,642
Last reply date
Last reply from
09civic
IMG_20260516_193114554_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0
IMG_20260516_192955471_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0

New threads

Top