anyone know bout Audio Legion?

[bigblackdodge]

Audio Legion AL3500.1D Amplifier

They seem legit and have dyno numbers posted but priced stupid cheap if they are real numbers. What you think?

I'm gonna try this 3500 on my 4 xfls.

Click to read more...

 

[hispls 5,000+ posts]

That is hardly an amazing price point to gamble on an untested and unknown amp which appears to be more of the same old Chinese junk.

 

[jersyn82]

That is hardly an amazing price point to gamble on an untested and unknown amp which appears to be more of the same old Chinese junk.

From what I've read I don't think they are Chinese junk. Although I've never ran one. But an amp that's rated at 3500 and does 4400 certified is good w me

 

[adulbrich 5,000+ posts]

Basically FSD //content.invisioncic.com/y282845/emoticons/fyi.gif.9f1f679348da7204ce960cfc74bca8e0.gif

 

[jersyn82]

Basically FSD //content.invisioncic.com/y282845/emoticons/fyi.gif.9f1f679348da7204ce960cfc74bca8e0.gif

So not Chinese then

 

[adulbrich 5,000+ posts]

So not Chinese then

I don't remember for sure, but I don't think so. Pretty sure they're Korean

 

[Massive spl]

That is hardly an amazing price point to gamble on an untested and unknown amp which appears to be more of the same old Chinese junk.

You trippin. It's a solid amp for the price

 

[jersyn82]

You trippin. It's a solid amp for the price

From what I've read that seems like a solid price to me too for what u get

 

[jersyn82]

Made in south korea! People should just keep to themselves when they can't help the OP with correct info. People are on here for help not guesses

 

[wew lad 5,000+ posts]

i have a hard time understanding how these are good prices considering what they used to cost..

 

[bigblackdodge]

I ordered the 3500 a hr ago. Soon as it comes in I'll do my little review. If it passes a few test then it will be impressive for the price. I have my new alty I need to install and a another g32 battery. Total of 3 batteries. Hope these new xfls hold up lol.

 

[Massive spl]

I ordered the 3500 a hr ago. Soon as it comes in I'll do my little review. If it passes a few test then it will be impressive for the price. I have my new alty I need to install and a another g32 battery. Total of 3 batteries. Hope these new xfls hold up lol.

lol 4 xfl's will be fine on that power. I'd put two on that power

 

[bigblackdodge]

lol 4 xfl's will be fine on that power. I'd put two on that power

Good to know. I know they are underrated at 1k RMS but wasn'tsure how much

 

[Popwarhomie 5,000+ posts]

Never heard of them..

Lol no they are great amps.

 

[kr15 5,000+ posts]

My 3500 arrives tmrw. The reason they are priced so competitively is that they are using open tool boards and just beefing them up. For example the

3500 is spec'd as a Zenon 3800 and the Flatline version (fl2) did right around 3.8-4k. The AL has beefed up caps and fets does 4.5k.

The 5000 which is specd as 4.8k is board. The Crescendo

Encore version does 4.5k while the AL does 5.5k. Again, stronger than stock parts.

I did a lot of reading before I bought one. The 8.5k is also the Ts 8.5k/tfe etc. I couldn't confirm but the 6.5 is likely the ts 6.5k.

They don't hide the fact that they are just beefing up existing Korean pcbs