$800 for kickass sub setup

[req 5,000+ posts]

x2 Great idea REQ //content.invisioncic.com/y282845/emoticons/yumyum.gif.0556df42231b304b9c995aefd13928a8.gif
Kali

well. i will be helping install them - so i do have somewhat of a say in it //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

we would prolly be ordering 8 of them (because a friend of mine wants two //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif )

 

[GCAdidas13 10+ year member]

i like dual avalanche 15 dual2ohm with 1300 watts

avalanches will suffice with 650 watts. . . .

 

[GCAdidas13 10+ year member]

wait req i just realized you were serious... would that setup be THAT good ?

thx

 

[req 5,000+ posts]

figures are recorded using 1-way Linear Xmax, and listed cone area, all converted to meters.

http://www.soundsplinter.com/rli_series/rli_8_inch_DIY_car_and_home_subwoofer_driver_information.html

Xmax: 17.8mm X 6 = 106.8mm = 0.11m

Sd: .02 m^2 x6 = .12m^2

SdxXmax = Vd (volume displacement - Maximum linear volume of displacement of the driver (product of Sd times Xmax), in cubic meters. "This parameter is the Peak Diaphragm Displacement Volume — in other words the volume of air the cone will move. It is calculated by multipying Xmax (Voice Coil Overhang of the driver) by Sd (Surface area of the cone). Vd is noted in cc. The highest Vd figure is desirable for a sub-bass transducer.)

Vd: [sd] .12m^2 x [Xmax] .11m = .013m^3 of air displacement., or 13 Liters.

lets see what a pair of AV15's will do?

Avalanche;

http://www.ascendantaudio.com/archive/Avalanche%2015.htm

Sd: 749cm^2 x2 = 1498cm^2 = 14.98m

Xmax: 27mm x2 = 54mm = .054m

Vd: [sd] 14.98 x [Xmax] .054 = 0.81m^3 of air displacement, or 810 Liters.

some reason - that sounds way off //content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif

 

[GCAdidas13 10+ year member]

Yup. Sounds off.

 

[GCAdidas13 10+ year member]

In the last 24 hours I have:

restored my free internet service without gathering attention ($Free)

purchased a brand new elite laptop with free accessories out the *** from Compaq ($1100)

purchased two Avalanche 15's for ($488)

In the next three weeks I will:

go on vacation with my girlfriend and family to Florida

go to New York to stay with req for a while and get a very sufficient amount of work done on both of our cars

get my RE 35.1d fixed

return to my house near the end of June to find my laptop and avalanche subwoofers

finish installing my frontstage and make everything look SESSI!

 

[SixthFloorFreak 10+ year member]

2 SX 15's if the VC config will work out

 

[GCAdidas13 10+ year member]

already bought two ava15's

they'll get 650w each and i have an HO alt to hold 14.4

so i'm happy.

boxbuilding with REQ in a week and a half //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 

[SixthFloorFreak 10+ year member]

didn't see the 3rd page, just hit reply on the 2nd

:/

 

[req 5,000+ posts]

oh well mr brian //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

we should be quite happy with the results.

werent you gonna have them shipped to my house?

 

[GCAdidas13 10+ year member]

Naw, I can't... Seems like they won't be ready to be shipped until the end of the month anyway.

So they're coming here, but, we can still make the enclosure //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

i think we need someone to tell us the EXACT diameter of the mounting holes on an Avalanche

 

[req 5,000+ posts]

Naw, I can't... Seems like they won't be ready to be shipped until the end of the month anyway.
So they're coming here, but, we can still make the enclosure //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

i think we need someone to tell us the EXACT diameter of the mounting holes on an Avalanche

you had one! wtf //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

i need the diamater of the RLs hole - mike better tell me //content.invisioncic.com/y282845/emoticons/mad.gif.c18f003ab0ef8a0d9c27ca78d77a6392.gif