4ohm hooked to 2 SVC-most powerful?

[dragnix 5,000+ posts]

Let me see if I can break it down in words, because it's hard to do so.

Run the RCAs from the headunit to the amp. Then from then amp have 2 y-adapters (the 2m1f type), one for ch. 1&2 on the amp, then another for ch. 3&4.

 

---------- Post added at 12:05 PM ---------- Previous post was at 12:05 PM ----------

 

fuck yea

 

[knokinnakamichi 10+ year member]

Let me see if I can break it down in words, because it's hard to do so.
Run the RCAs from the headunit to the amp. Then from then amp have 2 y-adapters (the 2m1f type), one for ch. 1&2 on the amp, then another for ch. 3&4.

 

Yes much better, I understand now. So, from the amp to the subs-what exactly am I doing? I could draw a picture to what I think I'm doing. Will I not run from channel 1/2 two negatives into one and then that one into one sub and then two positives from channel 1/2 to one and then that one into one sub AND then do the same from channel 3/4 to the other sub...? OR am I just running channel 1/2 one negative one positive to their respected spots on one sub and then the same for channel 3/4?? So confused....

 

[dragnix 5,000+ posts]

isn't there writing on the speaker output that says bridged? Take a pic and post it

 

[dragnix 5,000+ posts]

basically what you're going to do is take a pos and neg from both 1 and 2 and run it as one ch. and the same for 3 and 4 I hope that makes sense //content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif

 

---------- Post added at 12:18 PM ---------- Previous post was at 12:17 PM ----------

 

the amp has autobridging, that should make it easier. Read the instruction manual lol

 

[knokinnakamichi 10+ year member]

isn't there writing on the speaker output that says bridged? Take a pic and post it

What do you want a pic of?

 

[dragnix 5,000+ posts]

of the side with the speaker outs on the amp

 

[knokinnakamichi 10+ year member]

basically what you're going to do is take a pos and neg from both 1 and 2 and run it as one ch. and the same for 3 and 4 I hope that makes sense //content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif 

---------- Post added at 12:18 PM ---------- Previous post was at 12:17 PM ----------

 

the amp has autobridging, that should make it easier. Read the instruction manual lol

I've had the amp since 05 and lost the manual, because I've moved 3 times......

 

[dragnix 5,000+ posts]

let's do this, take the pos on ch.1 and neg. on ch.2 and connect that to 1 sub

then pos on ch.3 and neg. on ch.4 and connect that to the other sub

 

[knokinnakamichi 10+ year member]

***** BUNG HOLES I DONT HAVE THE MAN..I asked the forum if anyone knew where I could get one....anyway here is the pic ampout.jpg picture by walt55054life - Photobucket

 

[dragnix 5,000+ posts]

then do as I outlined above and the amps should output bridged power

 

[knokinnakamichi 10+ year member]

then do as I outlined above and the amps should output bridged power

So it's simple haha, I was trying to make it complicated and do pos from 1 & 2 into one and connected that into pos on sub. Then, neg from 1 & 2 into one and connect that into neg on sub. Then, do the same for the other sub from 3 & 4. I thought that would give max power, but you're saying just pos from 1 and neg from 2 into respected spots on one sub and same for 3 & 4???

 

[dragnix 5,000+ posts]

So it's simple haha, I was trying to make it complicated and do pos from 1 & 2 into one and connected that into pos on sub. Then, neg from 1 & 2 into one and connect that into neg on sub. Then, do the same for the other sub from 3 & 4. I thought that would give max power, but you're saying just pos from 1 and neg from 2 into respected spots on one sub and same for 3 & 4???

you got it

 

[knokinnakamichi 10+ year member]

you got it

Just out of curiosity what would happen if I did it the complicated way I was thinking?

 

[dragnix 5,000+ posts]

tbh i'm not too sure, but you can feel free to try it lol

 

[knokinnakamichi 10+ year member]

Well, I think I'll pass, but thanks! Does anyone know????