Recent content by Slayer16102

I will look into the big 3 being done here pretty soon. As I said previously you guys are awsome, so thank you for everything. My alpine's came alive when they were given 75 watts each. What a difference an amp truly makes for the speakers. People have no idea just how much it matters to the...

I let them install the Kenwood 8005M and tune it all up for me with my alpine speakers. They did an amazing job. At $1,120.00 the install cost was pretty high ($679 in wiring, amps, and other components +345 in labor + tax), but man does it bang who knew $52.99 audio legion S20's could bang so...

Yeah, that's where my issue comes in, man I only have a 110 amp alternator to power the entire car. Due to the valeo voltage regulator on my car, there really is no alternator upgrades possible without the car throwing up a charging fault with a custom alternator installed. I have tried to...

Looking for a decent 5 channel amps to go with these subs and my current setup. My setup: Speakers have been recently upgraded (1) Pioneer 6800 BS head unit - should I keep it or upgrade it? Seems to do vol 59 of 62 with no distortion. (2) Alpine SPS-65C component speakers in front doors 80w...

Thank you for all the answers. The knowledge of this forum is a great help for anyone from novices to bassheads. These are all of the basic prefabs are specifically made for the car. If you had to choose one which one would you choose. Forward firing partition box $219 subthump Volume: .71...

My memphis SRX 500.1D amp has screw down holes for 4 gauge wiring The car has 0 gauge wiring in it with 0 to 4 gauge screw on adapters. At one point I had a kenwood 9106D amplifier so they just put 0 gauge in. Now I only have a single memphis SRX 500.1D Is this pulling too much power from my...

Thank you guys keep those suggestions coming. I will check back on this again later tonight once I get home from work. As always thank you for all of your suggestions and all of your help with my car audio setup.

They also recommended a JL audio TW5 in a factory specd box as a best #1 overall option at my local shop. Would you agree here given all of the different box types shown above and the very limited space constraints of my vehicle. Please know that I am not brand specific. I am open to all...

The following is the boxes I can use along with my memphis 500w SRX amp What subs would you put in these boxes for nice deep hard hitting bass. I need your help in making the right decision here. I have several different boxes and options to choose from that will fit my car, but I don't know...

It needs to be either a single 8 or 10, dual 8 or 10, triple 8, or a single 12 in a small sub box. The box cross section for the trunk is only 15" for a box to fit inside before it can be pushed forward to the partition. Any box deeper than that won't go down inside the trunk to slide it...

My alternator is a stock 110 amp alternator My current headunit is a pioneer 6800BS 50x4 RMS My current speakers are 4 - kicker CS 6.5" coaxials 4 ohm's rated at 100 RMS I need a decent 4 channel amp to power these coaxials thats not too expensive. I'm open to using various brands so long as...

Thank you guys I will definately do all that was suggested.

Solved. I cut out all the excess stuff and ran one single wire for the tan down to positive on the speaker and one single wire to the grey for the negative on the speaker. If that big black rubber thing matters I can add it back to the loop again if needed it wasn't there with the default bose...

Here is more photos with it all easier to see. What's needed and what's not. Why is there barely any midbass when only one of these two connections is hooked up shouldn't the speaker play normally with one? How do I clean these connections up and fix them? This is with the CSC654 installed...

In an older install with alpine SPS 610-C's a shop did this. After cleaning up this mess when I installed kicker CSC6.5's in the doors I now have this. There is hardly any bass whatsoever from the mids. It seems like they cut two wires, then ran a new double set of wires off of each wire...