-
8Participant count
-
Participant list
Papermaker85 5,000+ posts
Banned
what drivers is the peak coming from.. where are you putting the mic? and why cant you get the peak out? it could be something in the cabin resonating..
OP
big scott
blazin low, and loud
- Thread Starter
- #4
anybody know what the 2 selections are in the start screen ?
you can pic 3 things.
dsp-88r-pre
dsp-88r-amp
offline mode.
what are the first 2 ?
i tryed both and i dont know what they mean.
also there something else i dont under stand.
this has 2 remote in wires.
i dont get why theres 2.
but it only has 1 remote out.
http://precisionpower.com/product/dsp-88r/
manual is here if anybody needs or wants to look at it.
you can pic 3 things.
dsp-88r-pre
dsp-88r-amp
offline mode.
what are the first 2 ?
i tryed both and i dont know what they mean.
also there something else i dont under stand.
this has 2 remote in wires.
i dont get why theres 2.
but it only has 1 remote out.
http://precisionpower.com/product/dsp-88r/
manual is here if anybody needs or wants to look at it.
Was interested in this unit, let us know what ppi says!
It won't take any adjustments without the remote plugged in and working the presets are saved there. You're probably not eqing **** lol, did you transfer your preset to the dsp and then set it with the remote
Just use pre, amp is probably for amps with dsps and offline mode won't work with the dsp it's made for initial settings and learning the program
I didn't bother using the remote out
Just use pre, amp is probably for amps with dsps and offline mode won't work with the dsp it's made for initial settings and learning the program
I didn't bother using the remote out
OP
big scott
blazin low, and loud
- Thread Starter
- #7
remote is plugged in and working.
and i have made a few presets and its working.
i was not sure what the pre and amp was.
the remote wire going to the amps does not work.
but i have a switch to turn the amps on after the dsp starts.
but the wired remote works.
and i have made a few presets and its working.
i was not sure what the pre and amp was.
the remote wire going to the amps does not work.
but i have a switch to turn the amps on after the dsp starts.
but the wired remote works.
OP
big scott
blazin low, and loud
- Thread Starter
- #8
its a good unit.
i just got a bad one.
like i said it all work and works great, except the remote turn on lead from dsp to amps.
so i just wired in a switch to turn amps on after dsp starts.
as the manual says the dsp needs to turn on first.
thats why the remote out wire has a 2 sec. delay.
i may just get a delay relay and be done.
that will take care of the problem.
as im sure its not going to be cheap to send it back, have them fix it....
delay relay cost $15 .
pickup1 5,000+ posts
CarAudio.com Veteran
Ive been hearing things about the plug...input plug needs to be firmly seated.
Been hearing a lot of plug issues with these on DIYMobileAudio
Been hearing a lot of plug issues with these on DIYMobileAudio
The Camry
Hey, I Try.
Coulda used a minidsp
OP
big scott
blazin low, and loud
- Thread Starter
- #13
buy it for me and ill use it..lol
ok guys...
i pulled the plug and got it in all the way.
im getting about 6 volts from it. it will not turn on my relay .
so i ran a wire right to one amp as my amps are daisy chained ( turn on ) and it turns them on no problem..
i dont get why only 6 volt.
dragnix 5,000+ posts
LXIX
this is a minidsp
Activity
No one is currently typing a reply...
About this thread
- Start date
- Participants
- Who Replied
- Replies
- 37
- Views
- 5,111
- Last reply date
- Last reply from
- big scott
