Yeah, Its a box ;)

[Psyence 10+ year member]

Here is a new box I made for a buddy... Dual Chamber ported box for 2 12W7s, 1.81cuft per chamber (net), 32hz.

Just gotta put the ends, seal, and put on carpet, did the mouting holes after the pics.

Click to read more...

 

[Bolognablake 10+ year member]

Nice.

Looks smaller than 2ft^3 each though.

 

[SAG3 5,000+ posts]

flush mounting?

 

[SAG3 5,000+ posts]

****

 

[Psyence 10+ year member]

I was going to flush mount. But unfortunately, the only way to do that is to make a removable baffle due to the way the subs are installed.... (Screws go under the surround, then a ring, then a clamp ring over that, you need quite a bit of room to put the clamp ring around the woofer... Hard to explain.

I may do it, just not quite sure yet //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[JL12W7INAGS300 10+ year member]

sexy!

 

[tommyk90 5,000+ posts]

Nice.
Looks smaller than 2ft^3 each though.

x2

Especially after factoring in the massive displacement of a W7

 

[Psyence 10+ year member]

Ill edit my first post. I was excluding the sub displacement when I posted, included when building tho.

The exact size is

1.812cuft including all displacements. The gross size is 2.391cuft, port displacement is .439cuft, and the sub displacement is .14

Tuned to 32hz.

I think it looks a little smaller than it really is sitting on that table saw. The depth is 29" the peak height is 15.5" and the width for each woofer is 14.125"

Its pretty big, and **** heavy.

 

[James Bang 5,000+ posts]

mighty sexy... the box. very very clean cuts.

 

[TheNoodPoopler]

where in canada you located man? im over in bc.

thats teh sexy //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[soul05 10+ year member]

wooooo very nice box

 

[PV Audio 5,000+ posts]

I'm not seeing any dual chamber...

 

[Pyro_By_Nature 5,000+ posts]

Now THAT'S what a box is supposed to look like!

Nice cuts //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

And pv..........it's quite obvious that it is in the last pic //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[ramos 5,000+ posts]

I'm not seeing any dual chamber...

I didn't either until I noticed the screws running down the middle, then the depth in the last picture. Looks nice so far man. Just a question, I see you didn't divide the port all the way. Isn't that going to mess up the tuning ? //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[joetama 5,000+ posts]

Now THAT'S what a box is supposed to look like!
Nice cuts //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

And pv..........it's quite obvious that it is in the last pic //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

I thought it was pretty obvious......