why does this not work

[kingbrew06 10+ year member]

Size 10 -inch MTX BLUE THUNDER RAN THREE ON THIS AMP

Impedance 4 ohms

Cone Material Polypropylene

Surround Material EPDM rubber

Sealed Box Volume (cubic feet) 0.5 - 1

Ported Box Volume (cubic feet) 1 - 2

Port diameter (inches) 3

Port length (inches) 10.75

Free-Air No

Dual Voice Coil No

Sensitivity 85 dB at 1 volt

Frequency Response 37 - 150 Hz

RMS Power Range (Watts) 75-250

Peak Power Handling (Watts) 500

Top Mount Depth (inches) 5 1/16

Bottom Mount Depth (inches) 5 9/16

Cutout Diameter or Length (inches) 9 1/4

Vas (liters) 23.7

Fs (Hz) 37.6

Qts 0.67

Xmax (millimeters) 9.44

Parts Warranty 2 YEARS

Labor Warranty 2 YEARS

Size 10 -inch KICKER C10s CAN NOT RUN THREE whats the difference???

Impedance 4 ohms

Cone Material Polymineral

Surround Material Foam

Sealed Box Volume (cubic feet) 1 - 2.4

Ported Box Volume (cubic feet) 1.25 - 1.75

Port diameter (inches) N/A

Port length (inches) N/A

Free-Air Yes

Dual Voice Coil No

Sensitivity 87.3 dB at 1 volt

Frequency Response 30 - 500 Hz

RMS Power Range (Watts) 50-150

Peak Power Handling (Watts) 300

Top Mount Depth (inches) 5 1/16

Bottom Mount Depth (inches) N/A

Cutout Diameter or Length (inches) 9 1/4

Vas (liters) 64.38

Fs (Hz) 29.4

Qts 0.451

Xmax (millimeters) 9.76

Parts Warranty 1 Year

Labor Warranty

Click to read more...

 

[kingbrew06 10+ year member]

my amp is a boss 2000w mono

 

[dman4486 5,000+ posts]

wat?

 

[ILLCRACKALUV 10+ year member]

What the **** are u trying to say?

 

[SomeGuyDude 10+ year member]

I think he's asking why his amp was running the three MTX subs and not his three CVRs.

What do you mean "cannot run three" though, OP? Didn't have enough power?

 

[kingbrew06 10+ year member]

it would run three mtx but not three kickers

 

[andrewmoore13 10+ year member]

well what happens when you wire the kickers?

goes into protect shuts off? explain man.

 

[kingbrew06 10+ year member]

yeah thats what happens it cuts off i think i need an amp that is 1 ohm stable does anyone know of a good one that would not run me more than 300

 

[Racerx250 10+ year member]

Cause you **** at car audio. That's why it doesn't work.

 

[Racerx250 10+ year member]

Or it could also be your grammar sucks.

 

[SomeGuyDude 10+ year member]

A one ohm stable amp to run three Dual4 subs at 300RMS a pop? Keep in mind with three subs the ohms get funny. If you do it in parallel on three subs then you dropped to 0.6666666ohms which is probably why the amp shut off.

 

[kingbrew06 10+ year member]

they are single not dual

 

[SomeGuyDude 10+ year member]

Oh shit, C10's. Sorry man, I was thinking CVRs. Regardless you were dropping to 1.3333 then and it could still kill an amp in that situation. Or at least make 'er shut down.

I -think- most of the Hifonics Brutus amps are 1ohm stable, and seems like a lot of people like those (although they get some shit on the boards). Get the 1200watt one and since it's 900 at 2ohm and 1200 at 1ohm, if you keep the gains low that should be fine.

 

[energizedsbs 10+ year member]

you need the 8 ohm ones for a 2.666 ohm load

 

[FurbiesAndBeans 10+ year member]

Oh shit, C10's. Sorry man, I was thinking CVRs. Regardless you were dropping to 1.3333 then and it could still kill an amp in that situation. Or at least make 'er shut down.
I -think- most of the Hifonics Brutus amps are 1ohm stable, and seems like a lot of people like those (although they get some shit on the boards). Get the 1200watt one and since it's 900 at 2ohm and 1200 at 1ohm, if you keep the gains low that should be fine.

The MTXs are the same VC config, so its not a problem with the amp since he would have the same ohm load... my guess is he wired them wrong or turned the gain up too much