Question!!!!!!!!!

[BigBoomer 10+ year member]

Okay... I have two SVC subs could i wire them like a DVC sub...............?

Too Hard To Explain...........

just list all the ways to wire subs ill figure it out...............................//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Click to read more...

 

[Natheo 10+ year member]

i'm new but dont you just wire them in parrelel? that puts you at 2 ohms....?

 

[Alphafrog1 10+ year member]

Originally posted by Natheo i'm new but dont you just wire them in parrelel? that puts you at 2 ohms....?

well you could wire them parallel or series, and each of those would get a different resistance. and what that resistance is depends on what type of voice coil the subs have (2 ohm, 4 ohm, ect.) tell the resistance of the VC and i can tell you what you can hook up to it....

 

[Brock 5,000+ posts]

Originally posted by Alphafrog1 well you could wire them parallel or series, and each of those would get a different resistance. and what that resistance is depends on what type of voice coil the subs have (2 ohm, 4 ohm, ect.) tell the resistance of the VC and i can tell you what you can hook up to it....

^^ what he said...

 

[khi 10+ year member]

im gonna assume 4ohmsubs...

eitha gets a 8 ohm load......or 2 ohm load....good luck hookin em up to da amp //content.invisioncic.com/y282845/emoticons/cool.gif.3bcaf8f141236c00f8044d07150e34f7.gif

p e a c e

k h i

 

[BigBoomer 10+ year member]

k i think they are 4ohms (MTX thunder6000 12's)...Amp(Kenwood Kac-629s) is

Ground Isolation Circuit

Power MOSFET Switching Power Supply

Stereo, Mono, or Tri-Mode Operation Bridged Power Output at 14.4V (1kHz, 0.8% THD): 150 Watts x 1

Maximum Output Power: 350 Watts

Power Output at 2 Ohms, at 14.4V (1kHz, 0.8% THD): 75 Watts x 2

Power Output at 4 Ohms, at 14.4V (20Hz-20kHz, 0.08% THD): 60 Watts x 2

this is what http://www.millionbuy.com/kenkac629s.html says...//content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif

 

[Randy Savage 5,000+ posts]

Originally posted by BigBoomer k i think they are 4ohms (MTX thunder6000 12's)...Amp(Kenwood Kac-629s) is

 

Ground Isolation Circuit

Power MOSFET Switching Power Supply

Stereo, Mono, or Tri-Mode Operation Bridged Power Output at 14.4V (1kHz, 0.8% THD): 150 Watts x 1

Maximum Output Power: 350 Watts

Power Output at 2 Ohms, at 14.4V (1kHz, 0.8% THD): 75 Watts x 2

Power Output at 4 Ohms, at 14.4V (20Hz-20kHz, 0.08% THD): 60 Watts x 2

 

this is what http://www.millionbuy.com/kenkac629s.html says...//content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif

75 watts will do nothing for those subs...

 

[BigBoomer 10+ year member]

Originally posted by snova031 75 watts will do nothing for those subs...

thats at 2 ohms, tho. If griged my subs (like it is now) would it be 8 0r 2 ohms????

Lemme go get all the spec sheets...BRB

 

[BigBoomer 10+ year member]

I dont know... cant find the ****ing spec sheet