Sold pair of eu-700s d4

[HawaiianBassHed 10+ year member]

terminals broke off on 3 of the 4 terminals, can be glued back on I don't wanna do it because they may just come off in shipping..

$65 shipped for the pair..

some older pix, cones are still cherry, actually got them like that with the busted terminals and glued them, then it happened again when I removed them from the 4th order BP I made...

just looking to get rid of um at this point. got an 8w7 a couple neo 3hp, a 4hp/tipro, a couple sidewinder 12"s and some HD3 motors I need to recone. and only having 3 cars one of which we're selling stock leave me with alot of extra subs lol. plus I gotta buy other stuff like a new deck again lol. thanks for lookin //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

Click to read more...

 

[michaellane 5,000+ posts]

how did they do? ever get em metered? lol and how much were ya feeding them?

 

[HawaiianBassHed 10+ year member]

an RF 201s fir a little while then a BLAU THA275 //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

nope never really cared to push them hard enough to warrant metering them. I do own a dual sensor TL however that wasn't the intent. like I said, I own plenty of subs well capable of doing spl. why would I want to do spl with something that isn't designed for such. my buddy just came and picked up the w7 and was asking wow, u must've been hammering it huh, his answer was pretty much the same. I never even made it bottom out and I have well more than enough clean power to do so... just really no need for me to push something so small so hard. I have a 4hp TIpro just sitting atm and have the power box and everything to use it properly, I just simply removed it to put in these so I could use my full back seat. now I'm doing a box for my neo 3hp 10" to go under the back seat (calcing everything and starting my cuts now as a matter of fact) will put up pix on it later possibly but I also gtg on a 2hr each way drive later tonight/evening to pick up a set of traction bars for my truck too. so pretty busy. just don't need these and there about to get really mdf covered as I'm gonna go cut the box and not even bother to move them LOL

I take it back, I did meter them in my wife's jetta at one point and they did a 136 iirc car sealed New TL @ dash music peak hold on the spl... didn't bother pushing them to the limit they're just a space saving toy to have around //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[burzendowski 10+ year member]

not bad for 2 6's

 

[HawaiianBassHed 10+ year member]

not good either lol wasn't pushing them into clipping or pushing them at all, the tone didn't get discolored or change and there was no bottoming out they were still getting louder with the volume roll, I'd just rather have functional subs to SELL than blown subs to throw away so I didn't push them //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif . I think IF someone or I wanted to push them in more of an spl setup they'd be closer to 140. specially in a full burp only setup I see 140 pretty reasonable if not easily attainable. I just don't have a need or want to do that. I'm more into moding my truck to be honest, I actually just sold a perfectly working yellowtop and my 8w7 w/HO box and picked up a set of offroad traction bars for my truck //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

should go on tomorrow and I'll put up some pixors //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif