My bookshelf project

[btnhfan 5,000+ posts]

Why is there a notch/gap inbetween?

Im guessing thats for another board?

 

[PV Audio 5,000+ posts]

me gusta mucho senor. i can't wait to see a review of these cones.

 

[PV Audio 5,000+ posts]

Why is there a notch/gap inbetween?
Im guessing thats for another board?

they are two separate ones //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

just the way he set it up for the photo

 

[Moe Lester 10+ year member]

Ports are in place. I decided to go with 45hz instead of 40. This allowed me to make them not quite as deep as they would have needed to be. Flaring the PVC on the router was quite scary as well since there was barely any of the PVC sitting on the router base lol.

 

[negativezeroz 5,000+ posts]

good job brad

 

[Moe Lester 10+ year member]

thx //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

Well I cant really go any further. I need a 1/4" straight router bit but I have no clue where mine went. The ports are permanently attached now. Tomorrow I may get a new bit so I can get a little more done on them.

 

[PV Audio 5,000+ posts]

thx //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif
Well I cant really go any further. I need a 1/4" straight router bit but I have no clue where mine went. The ports are permanently attached now. Tomorrow I may get a new bit so I can get a little more done on them.

//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif drill bit fell through?

 

[j3bus2k3 5,000+ posts]

Looks great bro, congrats. Just got a few questions....how do you flare the pvc for the port? Why not just use a slot port? Cant wait to hear how these perform, looking for ideas for my own bookshelfs.

 

[Moe Lester 10+ year member]

I did the flaring with a router and a 1/2" roundover but the cutting edge was sunk down only around 1/4" The pipe was barely on the router base so it was a little rough so i hit it up with some 60 grit paper and that knocked down any lumps quickly. Then 150 smoothed it out nicely.

 

[PV Audio 5,000+ posts]

tres interesante

 

[ballstothewall 10+ year member]

Looks good! Can't wait to see the finished project and hear how they sound!

 

[Moe Lester 10+ year member]

heres closer shot of the port flare since it seems to be a small topic of its own right now and you can see its now permanently attached to the box.



I havent flared the back yet because i am not sure how I am going to finish these. It will however get the full 1/2" roundover //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[swc204 10+ year member]

looking good man...nice job on the flaring of the pvc

 

[InhumanAcura 5,000+ posts]

thats alot of resin //content.invisioncic.com/y282845/emoticons/tongue.gif.6130eb82179565f6db8d26d6001dcd24.gif

 

[Moe Lester 10+ year member]

thats alot of resin //content.invisioncic.com/y282845/emoticons/tongue.gif.6130eb82179565f6db8d26d6001dcd24.gif

your sub box is ugly //content.invisioncic.com/y282845/emoticons/naughty.gif.94359f346c0f1259df8038d60b41863e.gif