Ok well I have a list for your pioneer sub:
********#1----Rockford Fosgate model BD1000.1*********
* Class bd technology
* 1000 watts x 1 at 2 ohms
* 500 watts x 1 at 4 ohms-( I think)
* selectable 50-250 Hz variable low-pass crossover, 24 dB/octave
* MEHSA mounting technology increases the heat transfer from the MOSFET output devices to the heat sink, for higher power output, lower operating temperatures, and greater reliability.
* TOPAZ noise-killing differential inputs eliminate 80% of ground loop noise between the head unit and the amp.
* NOMAD advanced protection circuitry monitors temperature, voltage, current and impedence, and provides "intelligent" shut-down protection without limiting system performance.
* preamp outputs for easy connection to a second amplifier
* wired remote control of Punch Bass (0-18 dB centered at 45 Hz) — gives you fingertip control of your bass impact
* subsonic filter removes frequencies below the range of human hearing for increased efficiency
* 100-amp fuse and fuse holder required
* dimensions: 14-7/16"W (10-7/8" without endcaps) x 2-7/16"H x 9-7/8"D
**********# 2---- Sony XM-3001SXDl*********
1000W Max Power (1000W x1 @2OHM )
* 500w rms power (500w x1 @4OHM)-( I think)
* D-class Amp
* Digital Bass and Treble
* 21-band Digital Equalizer
* 300W x1 into 4O , 5-200kHz, at 0.04% THD
********# 3---MTX THUNDER1000D*********
RMS POWER (12.5 Volts DC):
500 Watts x 1 into a 4 Ohm load with less than 0.5% Thd+N
1000 Watts x 1 into a 2 Ohm load with less than 1% Thd+N
Dynamic Power (IHF-202 Standard) measured at 14.4 Volts DC
850 Watts x 1 into a 4 Ohm load
1500 Watts x 1 into a 2 Ohm load
Signal to Noise Ratio:
100dB A-Weighted
Damping Factor:
>200
Frequency Response:
20Hz-200Hz
Maximum Input:
8Vrms
Thunder EQ:
Variable Bass Boost (0-18dB) centered at 40Hz
EBC External Bass Control
Crossover:
Variable 40Hz to 200Hz, 24dB/octave low pass
Dimensions:14" x 9" x 2" (35.6cm x 22.8cm x 5cm)
15-1/4" x 9" x 2" 38.7cm x 22.8cm x 5 cm) Including IsoFeet
*******#4---Audiobahn A1500HCX********
Amplifier Specifications
Amplifier Type: Mono
RMS Power: 500W x 1
Bridged RMS Power: 1000W x 1
THD at Rated RMS Power: 0.02%
Speaker Level Inputs: No
Preamp Outputs: Yes
Built-In Crossovers: HP/LP
Bass Boost: 0-18 dB
Frequency Response: 10-40,000 Hz
Channel Separation: 84 dB
Signal to Noise Ratio: > 100 dB
Fuse Rating: n/a
Well I know that is alot to read but I looked online and I think that any one of the amps I listed would do the job for you very well...These are all high-end amps that may be expensive but are also hig quality....I don't like recommending crap to people...Hope this info helps you..
Adam
//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif