Just got my PA A3000db in Pics*

[req 5,000+ posts]

your pictures **** //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

no go put it in your car.

 

[james33440 10+ year member]

Where did you buy it? I need an amp for my XXX 15. //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[nikosbuddy 5,000+ posts]

i might pic one up to see...i dont know yet.........whats the ratings and whats there like ya know, overratings or underratings cause for the money i dont think you can beat that let me know someone, cause im running about 2000+ to my 1 12" now and lord its low.... //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif gotta build a new box //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

Mike

 

[bamaboy 5,000+ posts]

monte_Carlo97, he is on here just send him a pm, but he might be on vacation so i dont know

but req, i dont need any fuse or anything? i thnk im going to go buy one this afternoon, and order the 1/0 wire next week, because i have no money //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

 

[zachzchw 5,000+ posts]

Where did you buy it? I need an amp for my XXX 15. //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

From MonteCarlo.....hes a PA dealer.....

why would I try to mess you up by telling you to install your amp? //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif

 

[bamaboy 5,000+ posts]

supposed to do 2300 rms @1ohm, 1800 @2ohm and 1200@4ohm

 

[bamaboy 5,000+ posts]

i thought i need a fuse becaus ethe amp dosent have one?

 

[bamaboy 5,000+ posts]

it also come with a warranty, so i think its a great deal

 

[zachzchw 5,000+ posts]

i thought i need a fuse becaus ethe amp dosent have one?

Didnt notice that you didnt have a fuse near the amp. Id wait till I got some protection in there........If you have 4 gauge in now, just go pick up a 4 gauge inline holder from BB or whatever.

 

[bamaboy 5,000+ posts]

im going to go ahead and get the distro block i think, so if i decide to go 1/0 like i should, i will be set, but if i dont need 1/0 wire i wont get it because thats less money to spend an time to run the fat wire

 

[zachzchw 5,000+ posts]

im going to go ahead and get the distro block i think, so if i decide to go 1/0 like i should, i will be set, but if i dont need 1/0 wire i wont get it because thats less money to spend an time to run the fat wire

Youll need the 1/0, if you plan on running it at 1 ohm. Find a wiring calculator, it will show you what gauge you need for whatever length it will be.

http://www.bcae1.com has one, I believe.

 

[bamaboy 5,000+ posts]

ya i need 1/0 wire i just have to get some money to get some

 

[AznRevlAzn 10+ year member]

you'll need 0/1 awg power wire and ground. The amp does not need fuses, only the power wire does. I recommend a 200 AMP ANL fuse wired less than 11 inches from the battery post. You can get the fuse and fuse holder at http://www.knukonceptz.com

If anymore questions just shoot them at me, skeptikal, and Dave.

 

[zachzchw 5,000+ posts]

you'll need 0/1 awg power wire and ground. The amp does not need fuses, only the power wire does. I recommend a 200 AMP ANL fuse wired less than 11 inches from the battery post. You can get the fuse and fuse holder at http://www.knukonceptz.com
If anymore questions just shoot them at me, skeptikal, and Dave.

So youre saying he doesnt need to fuse near the amp also?

 

[AZsound 10+ year member]

supposed to do 2300 rms @1ohm, 1800 @2ohm and 1200@4ohm

A3000db data (Lab tested)

Actual power: (12.5 V, THD = 1%, 4 Ohm/2 Ohm) Wt 469/745

THD: (80 Hz, P = 0,1 Pmax, 4 Ohm/2 Ohm) % 0,085/0,058

Input sensitivity: V 0,21 — 8,7

Signal-to-noise ratio: db 82,5

Frequency range: (+0/-1db) Hz 17 — 140

//content.invisioncic.com/y282845/emoticons/cool.gif.3bcaf8f141236c00f8044d07150e34f7.gif