Is this wiring possible????

[trigga_b 10+ year member]

Click to read more...

 

[wesl56 10+ year member]

why not just use one amp for each sub? you may be giving each coil of one of the subs different power that way

what amps are they?

 

[trigga_b 10+ year member]

shitty boss and a sony here's the specs.

BOSS- Amplifier Type: Mono

RMS Power @ 4 Ohms: 400W x 1 @ 4 Ohms

THD at 4-Ohm RMS Power: 0.01 %

Bridged RMS Power @ 4 Ohms: 600W x 1 @ 2 Ohms

Speaker Level Inputs: yes

Preamp Outputs : yes

Built-In Crossovers: LP

Bass Boost: 0 - 18 dB

Frequency Response: 20-20,000 Hz

Signal to Noise Ratio: 102 dB

Fuse Rating: n/a

SONY-200 watts RMS x 2 at 4 ohms

250 watts RMS x 2 at 2 ohms

500 watts RMS x 1 at 4 ohms

stereo or bridged mono output

Tri-way capable (Tri-Way Crossover required)

CEA-2006 compliant

requires 4-gauge power and ground leads Â? wiring and hardware not included with amplifier

MOSFET power and output stages

preamp- and speaker-level inputs

preamp outputs

gold-plated connectors

variable low-pass crossover (50-300 Hz, 12 dB/octave)

variable bass boost (0-10 dB at 40 Hz)

15-3/4"W x 2-3/16"H x 10-

 

[ramos 5,000+ posts]

Possible ? Yeah just a matter of connecting wires. Should it be done ? Not with my amps you won't . Looks like a fantastic plan to release the magic smoke from a couple amplifiers //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[Darkstarling 10+ year member]

how do you bridge a mono amp?

 

[ramos 5,000+ posts]

how do you bridge a mono amp?

Very, very carefully. It requires hot glue, and lots of popsicle brand popsicle sticks. And sprinkle of sunshine thrown in //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[ultimate157 5,000+ posts]

Do not do that.

Your amplifiers will not reproduce the song you are playing at the same exact point in time. Running each VC off of two amps is even worse than running a single DVC sub on two different channels.

Run one sub on its own amp, bridged channel or get a new amp.

 

[wesl56 10+ year member]

shitty boss and a sony here's the specs.
BOSS- Amplifier Type: Mono

RMS Power @ 4 Ohms: 400W x 1 @ 4 Ohms

THD at 4-Ohm RMS Power: 0.01 %

Bridged RMS Power @ 4 Ohms: 600W x 1 @ 2 Ohms

Speaker Level Inputs: yes

Preamp Outputs : yes

Built-In Crossovers: LP

Bass Boost: 0 - 18 dB

Frequency Response: 20-20,000 Hz

Signal to Noise Ratio: 102 dB

Fuse Rating: n/a

SONY-200 watts RMS x 2 at 4 ohms

250 watts RMS x 2 at 2 ohms

500 watts RMS x 1 at 4 ohms

stereo or bridged mono output

Tri-way capable (Tri-Way Crossover required)

CEA-2006 compliant

requires 4-gauge power and ground leads Â? wiring and hardware not included with amplifier

MOSFET power and output stages

preamp- and speaker-level inputs

preamp outputs

gold-plated connectors

variable low-pass crossover (50-300 Hz, 12 dB/octave)

variable bass boost (0-10 dB at 40 Hz)

15-3/4"W x 2-3/16"H x 10-

ya something is whack w/ those BOSS specs...

u may wanna look into some better and also matching amps if you really want to enjoy your L7s...

 

[trigga_b 10+ year member]

never heard of bridging a mono amp

 

[Worlddre 5,000+ posts]

you could just run each sub to one amp those two coils you have run in series would be the same as just running one of the subs in series

 

[wesl56 10+ year member]

never heard of bridging a mono amp

apparently whoever made those specs for the boss knos how to do it lol

 

[mikeyboc 10+ year member]

I understand it is occasionally a good idea to think outside the box, but WTF?

This looks like you stepped outside the box and landed in a pile of siht.

 

[trigga_b 10+ year member]

would it be safe to just run each vc of one sub to the 2 channel amp?

 

[trigga_b 10+ year member]

the reason i thougt of this is because that boss amps cuts off in like 5 ****ing mins, cuz its hot...so i was just going to use it as a "loud button" and run the 2 channel amp to each sub. The mono amp was going to be hooked into my subwoofer output on my hu, which i have a button to cut the sub output on/off. I guess ill just leave it like it is until I get that kicker amp