Sold FS: 600rms x 2 bridged for $120 bones+sh

[Fast1one 10+ year member]

This MAY be up for trade, but the other party seems uninterested, so here it is:

Cadence TXA-6004 with a slightly bent foot and a couple hairline scratches. Still mounts normal and scratches are barely noticeable, if at all from a distance. Works well and has seen little abuse from me. Looking for a stealthier install //content.invisioncic.com/y282845/emoticons/veryhappy.gif.fec4fed33b4a1279cf10bdd45a039dae.gif

Here you can see the biggest scratch, about 3 inches in length but pretty thin. You can't really see the scratches until you get closer. Its actually quite a beautiful amp IMO. And I am usually not a fan of chrome.

And here is the green light //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

Click to read more...

 

[bustaplz 10+ year member]

Also, anyone see a problem running 2 sets of speakers on 2 channels. My idea is to run my Front and rear parallel for 2ohms and run my subs on the other two channels. 4 ohm speakers, D4 ohm subs. Could be the most perfect setup I could imagine.

 

[nineball 10+ year member]

PM me with price shipped to 79707 and possibly the physical dimensions and we may have a deal. Have to make sure it would be comfortable under my seat. Does it run hot?

TXA-6004

4 CHANNEL HIGH POWER AMPLIFIER

SPECIFICATIONS:

*

4 Ohm RMS Power: 4 x 150 Watts @ 13.8 Volts

*

2 Ohm RMS Power: 4 x 300 Watts @ 13.8 Volts

*

4 Ohm Bridged RMS Power: 2 x 600 Watts

*

Frequency Response: 20Hz - 30kHz

*

Damping Factor: >200 @ 100Hz

*

S/N Ratio: >100 db

*

Channel Seperation: >65dB

*

Minimum THD:

*

Dimensions: 25" x 9.2" x 2.12"

FEATURES:

*

High Speed Mosfet Power Supply

*

Studio Grade Bipolar Output Stage Transistors

*

Fully Adjustable 18dB/Octave Crossover

*

Fully Adjustable Bass and Treble EQ Controls

*

Adjustable Input Gain 170mV-5V

*

Ultra Reflective Chrome Top Cover

*

2 Ohm Stereo Stable

*

4 Ohm Mono Bridgeable

*

3 Channel Mixed-Mono Capable

*

Power and Protection LED Indicators

*

Full IC Controlled Protection Circuitry

*

Mute and Soft Delay Circuitry

*

Lucite Encapsulated Terminals

 

[Fast1one 10+ year member]

Honestly it does run kinda hot so I would give it plenty of breathing room. Thats a lot of power for a class A/B, heats gotta go somewhere //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

If it still interests you then you are next in line if my trade falls through

BTW, thank you nineball

 

[nineball 10+ year member]

no problem, but i wonder why yours runs hot. i had a 3004 and a 6004 (bridged) and it never really got hot unless it was 90+ outside.

 

[bustaplz 10+ year member]

Honestly it does run kinda hot so I would give it plenty of breathing room. Thats a lot of power for a class A/B, heats gotta go somewhere //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif
If it still interests you then you are next in line if my trade falls through

BTW, thank you nineball

I'm running a total of 920-1240w of A/B power right now. Or was, until my MB Quart fried itself, so I think it should be somewhat equal. After seeing the dimensions, I think it could work out well. It looks as if a lot of heat is dissipated along the edge, which would have a good amount of breathing room. As long as there wouldn't be an issue running the two sets of speakers off the front channels, it would solve my amp issues. I could get more power to my comps, probably not have as many heat issues and ditch my sub amp and keep the same power to the subs. If your trade falls through, PM me a paypal address, you've got a buyer. //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

EDIT - May be a stupid question, but, can you run say, 2ohms on the rear channels and 4ohms on the front channels? I've never tried that before.

 

[Fast1one 10+ year member]

Yes you can mix and match front and rear channel impedance. All the heat is concentrated on the heat sink, so if that has sufficient room then it should be fine. Mines in a hot trunk right now so I am sure that doesn't help //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

BTW, nineball I live in California, so it is generally 90+ heat all day //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 

[nineball 10+ year member]

Yes you can mix and match front and rear channel impedance. All the heat is concentrated on the heat sink, so if that has sufficient room then it should be fine. Mines in a hot trunk right now so I am sure that doesn't help //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

i don't think you can do that but i could be wrong. i would ask jason before you attempt it.

 

[bustaplz 10+ year member]

i don't think you can do that but i could be wrong. i would ask jason before you attempt it.

Who is jason?

 

[Fast1one 10+ year member]

i don't think you can do that but i could be wrong. i would ask jason before you attempt it.

Why not? Its just like if you were to run the fronts at four ohms and bridge the rears at 4 ohms (effective 2 ohms per channel). Ive never had an amp complain when I do that.

Who is jason?

He is a Cadence rep, JasonPaul I think is his screen name either here or at diymobileaudio.com

 

[quins90lac 10+ year member]

just a general question about this amp but what is the max output at 4oms bridged

 

[Fast1one 10+ year member]

just a general question about this amp but what is the max output at 4oms bridged

Max output? what do you mean by that, the maximum clipped output? Its rated at 600rms per pair of channels. Now, if I had the equipment I could test the rail voltages to see what the maximum dynamic peak is, if thats what you mean...
Anyway, now SOLD

 

[quins90lac 10+ year member]

no i was just wondering cause my subs are 600rms and i was going to upgrade my amps in the future and im trying to get some options . and was wondering what the max wattage for it was

 

[nineball 10+ year member]

no i was just wondering cause my subs are 600rms and i was going to upgrade my amps in the future and im trying to get some options . and was wondering what the max wattage for it was

why are you concerned with max wattage? you should not even be looking at that stat. rms and/or continuous should be your worry.