fs 10" lms subwoofer

[tc3k101 5,000+ posts]

Item(s) for Sale:

10" lms

Item(s) Description/Condition:

Never mounted powered to break in and pull parameters. Waiting for Matt to send me fully broken in parameters and I will post them.

Uses a tc9 motor with three .75" slugs

500rms

svc 4ohm

Mid break in

Re:2.94 ohms

Fs: 28.0 Hz

SPL: 86 dB

Vas: 1.44 cu. ft.

Qms: 7.00

Qes: 0.45

Qts: 0.40

Xmax: 29mm

Price:

SOLD

Shipping and Miscellaneous Item Information:

Item Pictures:

(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).

Click to read more...

 

[bass maniak 10+ year member]

Sick 10" subwoofer here, SOME ONE BUY THIS! Great deal & he's a good dude to.

I was gonna take it myself before I ended up grabbing a woofer within canada instead. Shipping shouldnt be to bad to anyone within the states tho.

If your looking for a good 10" sub & in the US, you would be foolish to pass this one up!

 

[resko1 10+ year member]

Wow. I must commend Matt for getting the Qts down to .4

This is a supurb driver. And a good price. Instead of regular LMS needing a large sealed box since the q's are usually around .7 or higher, this should do well in a small to med ported box.

Took him long enough! Lol.

Bump fo jou!

 

[tc3k101 5,000+ posts]

Sick 10" subwoofer here, SOME ONE BUY THIS! Great deal & he's a good dude to.
I was gonna take it myself before I ended up grabbing a woofer within canada instead. Shipping shouldnt be to bad to anyone within the states tho.

If your looking for a good 10" sub & in the US, you would be foolish to pass this one up!

Thanks bud hope you enjoy your ixl 10"

Wow. I must commend Matt for getting the Qts down to .4This is a supurb driver. And a good price. Instead of regular LMS needing a large sealed box since the q's are usually around .7 or higher, this should do well in a small to med ported box.

Took him long enough! Lol.

Bump fo jou!

lol Yeah parameters shocked me a little. Was expecting a higher q lower sensitivity. I'd love to see the inductance and bl though lol

I'm going to install this ****** this weekend to test it out and see if I truely want to sell it or not. Posted to check the temperature in the water. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[resko1 10+ year member]

with no copper you should see around 2-3mH for inductance. BL will be below 14tm but its completely linear. Every LMS coil has a low Bl.

Let me know how it goes! //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[tc3k101 5,000+ posts]

with no copper you should see around 2-3mH for inductance. BL will be below 14tm but its completely linear. Every LMS coil has a low Bl.
Let me know how it goes! //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

I know bl isn't going to be high sadly, this motor had a shorting ring.

 

[lil98cabrio 10+ year member]

any trades?

 

[tc3k101 5,000+ posts]

I'm open to partial trades and cash on your end but nothing straight across.

 

[nateberrier 10+ year member]

I have a pioneer 860mp and alpine 9886 and an mb quart 1500.1 and a TC9 15

 

[resko1 10+ year member]

I know bl isn't going to be high sadly, this motor had a shorting ring.

Personally i would say bl is gonna be around 12 or 13tm. Depends on the weight of the softparts though or MMS. With the copper shorting ring you should see about 1-1.5mH for inductance.

 

[nateberrier 10+ year member]

mmm eddy currents.

 

[resko1 10+ year member]

Lol. Should have quite low inductance. My TC9+ with a shorting ring had an inductance of 1.12mH

 

[tc3k101 5,000+ posts]

I have a pioneer 860mp and alpine 9886 and an mb quart 1500.1 and a TC9 15

Shoot me some pictures via pm and what you are willing to work out.

Personally i would say bl is gonna be around 12 or 13tm. Depends on the weight of the softparts though or MMS. With the copper shorting ring you should see about 1-1.5mH for inductance.

I hope so but we shall wait and see. I may be needing more cones from you really soon //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[tc3k101 5,000+ posts]

Played it on a ap30001 tonight absolutely slams the lows

 

[LaserRed38 10+ year member]

//content.invisioncic.com/y282845/emoticons/yumyum.gif.0556df42231b304b9c995aefd13928a8.gif