Dropping a turck, the gay or FTW?

[jimmclrk1 10+ year member]

and you posted that donks are stupid...//content.invisioncic.com/y282845/emoticons/eyebrow.gif.fe2c18d8720fe8c7eaed347b21ea05a5.gif

What does that mean?

 

[DaGh0st 5,000+ posts]

bag it FTW

 

[9512ds 5,000+ posts]

What does that mean?

a donk is the title given to a vehcile that is lifted and put on excessively large rims as in the vehicle on http://www.eastcoastryders.com

 

[NJAV1 10+ year member]

I would have lifted instead of lowered but the cost was too rich for my blood, a suspension lift on one of these Avalanche will run you at least a couple grand + wheels and tires....I already had my 20 chrome's..so I dropped it. What you see here is a Groundforce 2/3 torsion drop.

 

[lostsoul 10+ year member]

FTW //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

I like lifted and lowered but that is ****ing retarded looking. And yes it depends on the truck not all trucks look good jacked up not all look good dropped...

 

[9512ds 5,000+ posts]

njav1 that is clean it looks real good

 

[revrider1 5,000+ posts]

bag it FTW

x2

 

[revrider1 5,000+ posts]

FTW //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

That thing can possibly even drive, I dont see a driveshaft.

 

[AcidicDreams 10+ year member]

Ok so i'm saving for rims and putting performance aside for a few months on my dakota. the new rim's i'm going to get later this summer are a 29.7" diameter after the tire and that's smaller than the tires i have now so i need the gap smaller. anyway, if ya wanted to know, these are the rims i'm getting : http://superbuytires.com/Boss/Type%20313/ in the black. anyway, i'm thinking i might lower the truck 2" in front and 2" in back or 2" in front and 4" in back. I'm wondering what i should use to do it and if it would be gay or look tight.
Thanks in advance.

dropping the back more than the front is the pinnacle of gayness.... I about //content.invisioncic.com/y282845/emoticons/sick.gif.b1847c8dabbfeeddbcf1a78052249e10.gif when I saw it for the first time visiting socal...

however some trucks look slick with an even drop... it really deoends on the truck

 

[AcidicDreams 10+ year member]

That thing can possibly even drive, I dont see a driveshaft.

I'm sure it's under construction.... I've seen 'em that high... I'm not sure what the point is though

 

[jimmclrk1 10+ year member]

Ok, for everyone that didn't get it, my post was a joke. That truck wasn't finshed. They ended up using air bags... and eventually put a driveshaft on it. I say drop it.

 

[ngsm13 5,000+ posts]

I would go with a 2/4 drop on the Dakota man //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif...

It's pretty cheap too, Springs up front... blocks in the rear. Thinking of doing it to my 92 //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif...

nG

 

[AcidicDreams 10+ year member]

see that looks good except for the gay *** bumper

 

[AcidicDreams 10+ year member]

20" chrome rim's won't exactly make it look smaller. and i can't get bigger as they won't fit. the truck is a dodge dakota, jacking up a dakota= the gay. lowering it to the ground= the gay. i don't want it so low that when i put the r/t engine in this year, and put a supercharger in later this year i lose control. that's why i'm lowering it, guess i should have been more clear on the details lol.
the factory size is a 30" tire, the one's i have on now are just 1 size up. if i lower the truck it'll make the wheel well look smaller that's why i'm wanting to do it aside from the added performance handling i'll get with a slight drop.

sounds like a good reason to drop it... black rims will look good... just keep it's bumper off the speed bumps

 

[j3bus2k3 5,000+ posts]

see that looks good except for the gay *** bumper

Kinda like it got face ****ed by a ricer....

I'm x3 on the Air bags. Do it right and you wont regret it.